Dascom TALLY MIP480 Hızlı Başlangıç Kılavuzu - Sayfa 2

Yazıcı Dascom TALLY MIP480 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Dascom TALLY MIP480 2 sayfaları.

Sayfayı Yazdır

Tractor Door

Locking Lever

Release the tractor locking levers

by pulling them up. Once the forms

tractor is positioned, lock it by

pushing down its locking lever.

To unload continuous forms: Press the PARK button. The continuous forms paper is retracted to the park position.

If the paper cannot be retracted in one operation, continue to press the PARK button until the paper is parked.

To remove the paper, raise the Tractor Doors and lift out the paper.

Make sure that the printer is turned on. Check that tractor-fed continuous forms, if loaded, are retracted to the park position.

Ejecting Single Sheets

If printing using software with form feed, each sheet is ejected automatically after a complete form is printed.

To manually eject sheets of paper press the LOAD/FF button to execute a forward form feed.

Switching from continuous forms to single sheets:

1. Tear off your printed pages.

2. Retract the forms paper to the park position by pressing the

PARK button (the Fault indicator turns on).

3. Move the Paper Select Lever to the single sheet position and

insert a sheet according to the directions above.

4. Raise the single sheet paper support to position #2 and insert

a sheet according to the directions above.

Changing the Ribbon Cartridge

Trouble Shooting

NO POWER

1. Ensure the power plug is properly seated in bottom of printer.

2. Check the in line fuse coming from the battery.

POOR PRINT QUALITY

1. Ensure the ribbon cartridge is properly seated on carriage

assembly.

2. Replace the ribbon.

3. Check the head gap position (Green tip lever on left – push

down and move lever 2 to 3 clicks upward or adjust

accordingly to darkness of print).

2-1 Loading Continuous Forms (Cont.)

Holding the paper against the Easy-Load

platform, fit the paper into the tractor. Close

the door. Repeat the procedure for the left

tractor

accommodate the width of the form. Move the

paper to make the paper flat. Do not stretch

the paper too taut. Push the locking lever

down to secure the tractor in place.

2-2 Unloading Continuous Forms

2-3 Loading a Single Sheet of Paper

Move the Paper Select lever

down. (Adjust Print Gap Lever

if necessary)

Raise the Single Sheet

Paper Tray until it locks

in position 2.

2-4 Switching Paper Types

Open print-gap lever fully

open. To remove the old

ribbon, squeeze both of

the ribbon's tabs and lift

the ribbon straight out of

its carriage.

Be careful of the print

head during this operation.

and

adjust

forms

tractor

Switching from single sheets to continuous forms:

1. If a sheet of paper is loaded, remove the paper by pressing

the LOAD/FF button.

2. Move the Paper Select Lever to the continuous forms position.

3. Move the single sheet paper support to the fully down

position #1.

4. Press the LOAD/FF button. The continuous forms paper

advances from the park position to the top-of-form position.

Ribbon Cartridge

PAPER JAMMING

1. Ensure the paper is aligned properly in the bottom tractors.

2. Ensure the tractor lids are closed and both tractors are in the locked position.

3. Ensure the head gap in not set too tight against the paper

(see step 3 in POOR PRINT QUALITY).

4. Ensure the ribbon is installed correctly.

5. Ensure the paper is not torn or ripped going into the printer.

PAPER NOT LOADING (Tractors Not Turning)

1. Open the cover, ensure green paper type switch (located on the

right side of the printer) is set for continuous feed paper.

2. Press the LOAD/FF button to see if tractors turn.

Automatic Tear-Off

Your printer is factory-set for automatic

paper positioning for tear-off after a complete

form is printed.

Manual Tear-Off

Press the LOAD/FF button to position the

paper perforation in front of the tear edge.

Tear the paper against the tear edge.

Line up the right sliding edge guide with

the rib on the paper support. Adjust the

left sliding edge guide to the width of the

paper. Insert the sheet into the raised

paper support. Make sure that the

bottom edge of the paper engages

snugly with the platen. The paper will

automatically advance to the top-of-form

position if the single sheet load option is

set to Automatic.

Before installing the ribbon cartridge,

release the two tabs on the side of

the cartridge, then move the roller to

the FREE position. If the tabs are not

released, the cartridge will not fit

onto the printer.

When

placing

cartridge on the carriage, make sure

that the thin ribbon does not become

bunched or folded at the print head.

Readjust the print gap to achieve

good print quality.

the

new

ribbon

GEK-05024 (EN)