Apollo Smoke Detector XP95 Kurulum ve Bakım Kılavuzu - Sayfa 4

Güvenlik Sensörleri Apollo Smoke Detector XP95 için çevrimiçi göz atın veya pdf Kurulum ve Bakım Kılavuzu indirin. Apollo Smoke Detector XP95 4 sayfaları. Input/output unit
Ayrıca Apollo Smoke Detector XP95 için: Kurulum Kılavuzu (2 sayfalar), Kurulum Kılavuzları (2 sayfalar), Kurulum Kılavuzu (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar), Hızlı Başlangıç Kılavuzu (5 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (2 sayfalar)

Sayfayı Yazdır
Apollo Smoke Detector XP95 Kurulum ve Bakım Kılavuzu
The fl ame detector has an angle of view of approximately 90°, as shown in the diagram
below.
Fig 2 Angle of view of XP95 Flame Detector
The fl ame detector should be positioned at the perimeter of the room, pointing directly at
the area of the anticipated fl ame or at the centre of the area to be protected. If the detec-
tor cannot 'see' the whole of the area to be protected, one or more additional detectors
may be required.
The fl ame detector is not affected by normal light sources but should be positioned so that
sunlight does not fall directly onto the viewing window.
Loop Design
The XP95 fl ame detector is powered from the loop; it draws 2.2mA in quiescent state and
4.2mA in alarm. In order to determine the number of fl ame detectors that can be con-
nected to a given loop, please refer to the Loop Calculation program, which can be
downloaded from the Apollo website or requested from Apollo's Technical Sales depart-
ment as a CD.
© Apollo Fire Detectors Limited 2000-2005/RHD
4
Address Setting
Before installing the fl ame detector it is necessary to set the address using the DIL switch,
which is accessed by removing the front cover, using a 5mm hexagonal key. 7 segments of
the switch are set to 0 or 1, using a small screwdriver or similar tool.
A complete list of address settings is shown in the following table.
DIL switch
DIL switch
setting
setting
addr
1234567
addr
1234567
addr
1
1000000
11
1101000
2
0100000
12
0011000
3
1100000
13
1011000
4
0010000
14
0111000
5
1010000
15
1111000
6
0110000
16
0000100
7
1110000
17
1000100
8
0001000
18
0100100
9
1001000
19
1100100
10
0101000
20
0010100
51
1100110
61
1011110
52
0010110
62
0111110
53
1010110
63
1111110
54
0110110
64
0000001
55
1110110
65
1000001
56
0001110
66
0100001
57
1001110
67
1100001
58
0101110
68
0010001
59
1101110
69
1010001
60
0011110
70
0110001
101
1010011
106
0101011
111
102
0110011
107
1101011
112
103
1110011
108
0011011
113
104
0001011
109
1011011
114
105
1001011
110
0111011
115
Table 2 DIL switch address settings
We recommend that the address be set before the fl ame detector is mounted on the wall.
Sensitivity Setting
The eighth segment of the DIL switch referred to in the previous section is used to set the
sensitivity of the fl ame detector to class 1 or class 3. For most practical purposes the switch
should be set to class 1, the sensitivity required to detect fl ames as described in the section
'Quantities required and positioning of detectors'.
In exceptional cases the fl ame detector may be set to class 3 operation in order to avoid
nuisance alarms being caused by radiation sources that are close to the detector and
cannot be moved.
To set the DIL switch to class 1, switch to position '1'. To set to class 3, switch to position '0'.
Installation
The fl ame detector is mounted using either the mounting plate, which is supplied with the
detector, or the adjustable mounting bracket, part no 29600-203, which is bolted to the
mounting plate.
The standard mounting plate (supplied) is used for horizontal viewing, eg, along corridors or
along the length of industrial processes or vertical viewing inside fume cupboards or over
hoppers. It has two fi xing holes of 8.5mm diameter at 74mm centres.
DIL switch
DIL switch
setting
setting
1234567
addr
1234567
addr
21
1010100
31
1111100
41
22
0110100
32
0000010
42
23
1110100
33
1000010
43
24
0001100
34
0100010
44
25
1001100
35
1100010
45
26
0101100
36
0010010
46
27
1101100
37
1010010
47
28
0011100
38
0110010
48
29
1011100
39
1110010
49
30
0111100
40
0001010
50
71
1110001
81
1000101
91
72
0001001
82
0100101
92
73
1001001
83
1100101
93
74
0101001
84
0010101
94
75
1101001
85
1010101
95
76
0011001
86
0110101
96
77
1011001
87
1110101
97
78
0111001
88
0001101
98
79
1111001
89
1001101
99
80
0000101
90
0101101
100
1111011
116
0010111
121
0000111
117
1010111
122
1000111
118
0110111
123
0100111
119
1110111
124
1100111
120
0001111
125
126
5
DIL switch
setting
1234567
1001010
0101010
1101010
0011010
1011010
0111010
1111010
0000110
1000110
0100110
1101101
0011101
1011101
0111101
1111101
0000011
1000011
0100011
1100011
0010011
1001111
0101111
1101111
0011111
1011111
0111111