Apollo XP95A Series Kurulum Talimatları

Güvenlik Sensörleri Apollo XP95A Series için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Apollo XP95A Series 2 sayfaları. & soteria ul 268 7th edition detectors
Ayrıca Apollo XP95A Series için: Kurulum Talimatları (2 sayfalar)

Sayfayı Yazdır

Technical Data XP95A Detectors

Detector Model No

SA5050-250APO

Detector Type

XP95A Smoke Detector

Equivalent Obsolete

55000-650

Dectector

UL Listed Voltage

17 - 28 V dc

Modulation Voltage

5 - 9 V

(V peak to peak)

Maximum Alarm

4 mA

Current LED on*

Surge Current*

1 mA

Supervisory Current*

340 μA

Additional Remote

5 mA

LED Current*

Heat Element Rating

N/A

UL 1.23%/Ft -2.09%/Ft

Sensitivity

ULC 1.44%- 2.3%/Ft

Smoke-automatic ﬁ re detec-

UL/ULC Instruction

tor for use with a S5022 UL/

ULC listed base

Please refer to the panel manufacturer instructions

Spray with any of the following smoke products:

Test Method

• Solo Detector Testers Solo A10 • Smoke Sabre Smoke

Detector Tester • Solo Detector Testers Solo 365 • Solo

Detector Testers Testiﬁ e

Control Panel

Refer to www.apollo-ﬁ re.co.uk for compatible panels

Technical Data Soteria UL Detectors

Detector Model No

SA5150-650APO**

Soteria UL

Detector Type

Smoke Detector

Equivalent Obsolete

58000-650

Dectector

UL Listed Voltage

17- 28 V dc

Modulation Voltage

5 - 9 V

(V peak to peak)

Maximum Alarm

4 mA

Current LED on*

Surge Current*

1 mA

Supervisory Current*

500 μA

Additional Remote

5 mA

LED Current*

Heat Element Rating

N/A

Sensitivity

As SA5050-250APO

Smoke-automatic ﬁ re detec-

UL/ULC Instruction

tor for use with a S5022 UL/

ULC listed base

Test Method

Please refer to test methods in the table above

Control Panel

Refer to www.apollo-ﬁ re.co.uk for compatible panels

* All current measurements made with polling off

**Isolation feature is only available in SA5150-650APO and SA5150-750APO

39215-345/Issue 2

SA5050-350APO

SA5500-450APO

XP95A Multi-Criteria

XP95A Heat Detector

Detector (Smoke/Heat)

55000-886

55000-450

17 - 28 V dc

5 - 9 V

4 mA

2.5 mA

1 mA

500 μA

250 μA

5 mA

Rate of Rise (RoR) 20ºF/min

131ºF (55ºC)

(11ºC/min)

UL 1.23%/Ft -2.09%/Ft

N/A

ULC 1.44%- 2.3%/Ft

Smoke-automatic ﬁ re

Heat-automatic ﬁ re

detector head with integral

detector for use with a

heat detector for use with a

S5022 UL/ULC listed base

Hair Dryer

SA5150-750APO**

SA5800-450APO

Soteria UL Multi-Criteria

Discovery/Soteria UL

Detector (Smoke/Heat)

Non-isolating Heat Detector

58000-750

58000-450

17 - 28 V dc

17- 28 V dc

5 - 9 V

4 mA

3.5 mA

1 mA

500 μA

5 mA

Modes 1,3,4 Rate of Rise (RoR)

20ºF/min (11ºC/min). Mode 5

135ºF (57ºC) - 210ºF (99ºC)

135ºF (57ºC)

As SA5050-350APO

N/A

Smoke-automatic ﬁ re

Heat-automatic ﬁ re detector

detector head with integral

for use with a S5022 UL/ULC

heat detector for use with a

listed base

S5022 UL/ULC listed base

XP95A & Soteria UL 268 7th Edition Detectors

Installation Instructions

General

These instructions apply to the Apollo Soteria UL Bases. Please refer to the table below for

instructions on how to install:

Applicable Wiring Diagram (page 3)

Fig. 1 - New Installs (supports isolation)

Fig. 2 - Retroﬁ ts or Isolator bypassed

with a Remote LED

Fig. 3 - Retroﬁ ts or Isolator bypassed

with a Common Remote LED

Installation

These products must be installed in accordance with the applicable NFPA standards, local

codes and jurisdictional authorities. Failure to follow these instructions may result in failure of

the detectors to report an alarm condition. Apollo Fire Detectors Limited is not responsible

for detectors which are improperly installed, maintained or tested.

Before installing these products, check the continuity, polarity and insulation resistance

of all wiring. Check that installation is in accordance with the ﬁ re system drawings and

conforms to all applicable local codes such as NFPA 72.

Use 3" octagonal box for direct connection to the base. 4" octagonal and 4" square boxes

may be used with compatible UL listed mounting brackets. When mounting on a wall, install

4" to 12" from the ceiling. Secure the base to the electrical box with appropriate screws.

Do not overtighten the screws. For information on how to set the address of each device

correctly refer to the section 'XPERT 8 Card Addressing' overleaf.

If you are using shielded cable, please follow the instructions below:

Connect the shield to the

terminal on the base.

When shielded loop cable is used, connection of the shield, also known as the functional

earth (FE), must be terminated in accordance with the control panel manufacturer's

recommendations and local codes.

Unless instructed otherwise, ensure that all segments of the loop cable has functional

earth (FE) continuity and take care that it is isolated from building earth (also known as

protective earth (PE)) points such as metalwork, cable trays or junction boxes.

PLEASE NOTE:

Smoke detectors are NOT to be used with detector guards.

During construction work it is essential that the detector has it's dust cover ﬁ tted. The

build-up of dust inside a detector can lead to a trouble signal or false alarm.

Applicable Products

SA5000-210 – Soteria UL Base - 4"

SA5000-230 – Soteria UL Base - 6"

SA5000-210 - Soteria UL Base - 4"

SA5000-230 - Soteria UL Base - 6"

SA5000-210 - Soteria UL Base - 4"

SA5000-230 - Soteria UL Base - 6"