Apollo 58000-040 Kurulum Kılavuzu - Sayfa 2
Denizcilik Ekipmanları Apollo 58000-040 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Apollo 58000-040 2 sayfaları. Open area voice sounder
Ayrıca Apollo 58000-040 için: Kurulum Kılavuzu (2 sayfalar)
Sayfayı Yazdır
In setup mode the volume can be adjusted by holding the magnet adjacent to the ashing setup
LED and removing it at the desired volume level. If min or max volume is reached, the con rmation
LED stops ashing. To alter the direction of adjustment, remove the magnet for one second and re-
apply. Saving the volume setting is performed at the control panel.
Please check with panel manufacturer for compatibility of the above setup/test modes.
Fig 1. PCB outline
Fig 3.
Discovery Open Area Voice Sounder
Technical Data
Operating voltage
Switch-on surge
Quiescent current (non-polling)
Alarm current (non-polling) max
Sounder
Visual Indicator
Sounder with Visual Indicator
Alarm power
Sounder
Visual Indicator
Sounder with Visual Indicator
IP Rating
For sound pressure levels measured to EN54–3 see document PP2203
and for isolator operation information see document PP2090,
both available on request.
Fig 2. Example of Address 78
17–28V DC
1.5 mA < 10s
1.4 mA Nominal
9.5 mA
8.8 mA
13.4 mA
266 mW
246 mW
375 mW
21C
2
Individual Address Setting
The address of the Open Area Voice Sounder is set using segments 1-7 of the DIL switch.
Each switch is set to "0" (ON) or "1", using a small screwdriver or similar tool. A complete list
of address settings is shown below.
DIL switch
DIL switch
setting
setting
addr 1234567
addr
1234567
addr
1
1000000
11
1101000
21
2
0100000
12
0011000
22
3
1100000
13
1011000
23
4
0010000
14
0111000
24
5
1010000
15
1111000
25
6
0110000
16
0000100
26
7
1110000
17
1000100
27
8
0001000
18
0100100
28
9
1001000
19
1100100
29
10
0101000
20
0010100
30
51
1100110
61
1011110
71
52
0010110
62
0111110
72
53
1010110
63
1111110
73
54
0110110
64
0000001
74
55
1110110
65
1000001
75
56
0001110
66
0100001
76
57
1001110
67
1100001
77
58
0101110
68
0010001
78
59
1101110
69
1010001
79
60
0011110
70
0110001
80
101
1010011
106
0101011
111
102
0110011
107
1101011
112
103
1110011
108
0011011
113
104
0001011
109
1011011
114
105
1001011
110
0111011
115
Fault Finding
Problem
Possible Cause
No response or missing
Incorrect address setting
Incorrect loop wiring (polarity reversed)
Analogue value 1
Sounder failed
Analogue value 2
Visual Indicator failed (Sounder with Visual Indicator
version only)
Analogue value 3
Sounder with Visual Indicator failed (where visual
indicator exists)
Device fails to operate
Control panel has incorrect cause
and effect programming
Analogue Values
Analogue Value
Status
0
Flash Memory Fail
1
Sounder Fail
2
Visual Indicator Fail
3
Sounder and Visual Indicator Fail
4
General Fault
*Volume 1 does not comply with the requirements of EN54-3
DIL switch
DIL switch
setting
setting
1234567
addr
1234567
addr
1010100
31
1111100
41
0110100
32
0000010
42
1110100
33
1000010
43
0001100
34
0100010
44
1001100
35
1100010
45
0101100
36
0010010
46
1101100
37
1010010
47
0011100
38
0110010
48
1011100
39
1110010
49
0111100
40
0001010
50
1110001
81
1000101
91
0001001
82
0100101
92
1001001
83
1100101
93
0101001
84
0010101
94
1101001
85
1010101
95
0011001
86
0110101
96
1011001
87
1110101
97
0111001
88
0001101
98
1111001
89
1001101
99
0000101
90
0101101
100
1111011
116
0010111
121
0000111
117
1010111
122
1000111
118
0110111
123
0100111
119
1110111
124
1100111
120
0001111
125
126
Analogue Value
Status
17
Sounder Volume 1*
18
Sounder Volume 2
19
Sounder Volume 3
20
Sounder Volume 4
21
Sounder Volume 5
22
Sounder Volume 6
23
Sounder Volume 7
3
DIL switch
setting
1234567
1001010
0101010
1101010
0011010
1011010
0111010
1111010
0000110
1000110
0100110
1101101
0011101
1011101
0111101
1111101
0000011
1000011
0100011
1100011
0010011
1001111
0101111
1101111
0011111
1011111
0111111