Daspi Big Foot 1600 Kullanım Kılavuzu - Sayfa 7

Kapı Açıcı Daspi Big Foot 1600 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Daspi Big Foot 1600 13 sayfaları. Gear motor for sliding door
Ayrıca Daspi Big Foot 1600 için: Kullanım Kılavuzu (15 sayfalar)

Sayfayı Yazdır

INSTALLATioN

To operate a good installation of the gear motor BIG

FOOT follow these instructions:

Locate inside the property the correct point to install

BIG FOOT, usually near to the support column of the

gate.

Assemble the support plates "Pb" with the anchorage

pins and adjusting grubs

Build up a cement emplacement with sizes like fig.

3, foreseeing the passing of the protective coverings

"G" for the passing of the power supply and control

system cables.

Before the cement solidifying, install the bracket

"Pb" immersing the anchorage pins in the cement

and making sure that the bracket "Pb" is oriented

and perfectly on level

(fig.

After that the cement will be perfectly solidified

install the gear motor BIG FOOT on the bracket

"Pb" and after removing the protection cover fix the

operator softly by supplied nuts "Vf"

Loose the screws "Vp" and make the operator

BIG FOOT run in the suitable holes to establish a

distance between the operator's pinion "P" and the

gate suitable to the type of rack "C" you want to

install. The tooth of the pinion must mesh with the

teeth of the rack for all its width, so fix the nuts "Vf"

(fig.

5).

Carry out an emergency or manual manoeuvre (see

the par. " Emergency or manual manoeuvre") and

put the gate in the maximum opening position.

Lean one end of the rack "C" on the pinion "P" , make

sure that it's horizontal and fix it by welding or by

the suitable screws "Vc"

slide the gate, checking that the rack don't force on

the pinion and that don't go away.

If the gate is crooked put between the gate and the

rack some thickness to assure the constant centring

between the rack and the pinion.

After fixing definitively the rack "C" loose slightly

the nuts "Vp" and adjust the play-gap between rack

and pinion (2 mm apron.) using the grubs "Gr" to

position correctly the operator

When everything has been done fix the nuts "If" and

the nuts "D1" and with a manual manoeuvre open

and close the gate to verify the correct alignment

(there have not been friction).

IMPortant

The duration of the rack and the pinion depend on

the right mesh engagement.

in view of the considerable weight of the gates we

recommend to use iron racks or steel racks with an

adequate thickness.

The gates must have mechanical stops "Fa"

in opening and closing to avoid its derailment.

The mechanical stops "Fa" must ensure an antic

rushing space between the mobile and fix part

of the gate, in conformity with the regulations in

force.

(fig.

1).

3).

(fig.

4).

(fig.

6), fixing the rack make

(fig.

7).

(fig.

Put the gate in opening position and, according to

the gate weight, leave a space of 30-50 mm between

the gate and the mechanical stop "Fa"

the rack the limit switch support "S" by grubs "Gr1"

(fig.

9) in order to push the limit switch

Repeat the same operation on the other side, for the

closing limit switch support.

Make the circuitry like in the control panel manual

and install the obligatory safety devices.

Teach the people intended for the use of the

automation about the controls, safety devices,

emergency manoeuvre and dangerousness deriving

from the utilize of the automation.

Compile the technical booklet and fulfil the eventual

obligations deriving from the regulations in force.

We Guartntee the correct functioning of BiG FooT

versions only and exclusively if provided by dASpi

and only if combined with the original control

panel.

EmErGENcy or mANUAL mANoEUVrE

You have to do the emergency or manual manoeuvre

or during the installation, or only if the automation

does not work properly or if there is not power

supply.

cut off the power supply.

Open the plug on the handle "LS" cover and insert

the supplied key "CH"

Turn the key "CH" anticlockwise and take out the

handle of 90° towards you

manually.

In order to re-establish the normal functioning of

the automation, you have to put again the handle

"LS" in the original position and turn the key "CH"

clockwise, so take away the key and close the plug

on the handle.

Place the key "CH" in a safety place known

exclusively from the people intended for the use of

the automation.

Switch on the power supply, pay attention that

there's nobody where the gate is moving.

(fig.

8). Fix on

(fig.

9-b).

(fig.

10).

(fig.

10) and open the gate