Duren Tools 321265 Kullanım Kılavuzu - Sayfa 4

Matkap Duren Tools 321265 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Duren Tools 321265 7 sayfaları. 3/8” reversible air drill

Sayfayı Yazdır
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
4
It is strongly advised that you always use a Whip Hose/Leader Hose in combination with
Safety
Quick Release Couplings. See Fig. 2 for recommended setup.
5
Water in the air supply will cause the internal bearing of the tool to rust and eventually
WARNING! Ensure Health & Safety, local authority, and general workshop practice
n
seize.
regulations are adhered to when using this equipment.
6
Make sure that your airline is free from water at all times.
WARNING! Disconnect from air supply before changing drill bits, servicing, or performing any
7
Always select the correct sanding disc grit for the job.
n
maintenance.
Maintain the drill in good condition (use an authorised service agent).
Tools Included with your Sander
4
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be
4
dangerous and will invalidate the warranty.
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is
4
adequate lighting.
Before each use check condition of drill bit. Sharpen if necessary. If worn or damaged replace
4
immediately.
Ensure there are no flammable or combustible materials near the work area.
4
1 x High Flow Male Air Fitting
WARNING! Always wear approved eye (and/or face) and hand protection when operating the
n
drill.
Maintenance
Use face, dust, or respiratory protection in accordance with COSHH regulations.
4
Depending on the task, the drilling noise level may exceed 84dB in which case wear safety
1
If the air supply is not lubricated sufficiently it will be necessary to lubricate the tool
4
ear defenders.
directly. This can be done by disconnecting the air hose and pouring in 5ml of air tool oil
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/
into the Air Inlet. Read safety data sheet or instructions on use of oil to ensure safe
4
or tie back long hair.
usage. These can be obtained from your supplier.
Wear appropriate protective clothing and keep hands and body clear of working parts.
2
Replace worn or damaged parts using genuine parts only.
4
Maintain correct balance and footing. Do not over reach, ensure the floor is not slippery, wear
3
Store tool in a dry area, do not allow tool to be immerse in water or used/stored in wet
4
non-slip shoes.
conditions.
Keep children and unauthorised persons away from the work area.
4
Ensure work piece is secure before operating the drill. Never hold a work piece by hand.
4
Check the work piece to ensure there are no protruding screws, bolts, nuts etc.
4
Avoid unintentional starting.
4
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended
n
pressure 70-90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use
4
and ensure all connections are secure.
Prolonged exposure to vibration from this drill poses a health risk. It is the owner's
4
responsibility to correctly assess the potential hazard and issue guidelines for safe periods of
use and offer suitable protective equipment.
DO NOT use the drill for a task it is not designed to perform.
5
DO NOT operate drill if any parts are damaged or missing as this may cause failure and/or
5
personal injury.
WARNING! DO NOT drill any materials containing asbestos.
n
DO NOT carry the drill by the hose, or pull the hose sharply from the air supply.
5
DO NOT force, or apply heavy pressure to the drill; let the tool do the work.
5
DO NOT place air line attachments close to your face and do not point at other people or
5
animals.
DO NOT operate drill when you are tired or under the influence of alcohol, drugs or
5
intoxicating medication.
DO NOT carry the drill with your finger on the trigger.
5
DO NOT direct air from the air line at yourself or others.
5
When not in use disconnect from air supply and store in a safe, dry, childproof location.
4
Duren Tools
T: 01582 484875 E: [email protected]
www.duren.co.uk