4gon RouterBOARD 493 Hızlı Kurulum Kılavuzu ve Garanti Bilgileri
Ağ Yönlendiricisi 4gon RouterBOARD 493 için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu ve Garanti Bilgileri indirin. 4gon RouterBOARD 493 2 sayfaları.
Sayfayı YazdırRouterBOARD 493
Quick Setup Guide and Warranty Information
Assembling the Hardware
●
Insert the MiniPCI cards. RouterBOARD 493 provides three MiniPCI slots.
●
Connect antenna cables to the MiniPCI cards.
●
Install the board in a case and connect other peripherals and cables.
●
Plug in power cable to turn on the board.
Powering
The board accepts powering from the power jack, or from the LAN1 Ethernet port:
●
direct-input power jack J901 (5.5mm outside and 2mm inside diameter,
female, pin positive plug) accepts 9..28 V DC (overvoltage protection starts
at 28.5V-29V).
●
LAN1 Ethernet port J601 accepts 9..28 V DC input (at the board; higher
voltage is needed to compensate for power loss on long cables – at least
18V suggested) from non-standard (passive) Power over Ethernet injectors
(no power over datalines). The board does not work with IEEE802.3af
compliant 48V power injectors.
CAUTION: all power inputs are always active, but only one of them may be used
at a time to avoid damage of equipment.
The maximum output of the power supply available for extension cards is
normally 10W (3.0A).
Booting process
First, RouterBOOT loader is started. It displays some useful information on the
onboard RS232C asynchronous serial port. The serial port is set by default to
115200bit/s, 8 data bits, 1 stop bit, no parity.
Note that the device does not fully implement the hardware (RTS/CTS) flow control,
so it is suggested to try to disable hardware flow control in the terminal emulation
program in case the serial console does not work as expected, and if it does not
help, make a new cable using the pinout given in the User's manual.
The loader may be configured to boot the system from the onboard NAND, and/or
from network. See the respective section of User's manual on how to configure
booting sequence and other BIOS parameters.
DHCP or BOOTP (configurable in loader) protocols allow the RouterBOARD 192
series board to get an initial IP address, and provide the address of a TFTP server to
download an ELF boot image from. It is especially useful for software installation.
See the User's manual for more information and protocol details. Note that you
must connect the RouterBOARD you want to boot and the BOOTP/DHCP and TFTP
servers to the same broadcast domain (i.e., there must not be any routers between
them – they must be on the same Ethernet switch).
Extension Slots and Ports
●
Nine Ethernet ports, supporting automatic cross/straight cable correction
(Auto MDI/X), so you can use either straight or cross-over cables for
connecting to other network devices. The first Ethernet port (marked with the
"PoE" label and detached from the 8-port block) accepts 9..28 V DC powering from a passive PoE injector. The other
eight Ethernet ports (placed as a block) do not support PoE powering.
●
Three MiniPCI Type IIIA/IIIB ports with 3.3V power signaling.
●
DB9 RS232C asynchronous serial port.
Operating System Support
Currently tested operating system is MikroTik RouterOS (starting from ROS version 3.0).
4Gon www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299
rev. A (17-Sep-2008)