Cavity Sliders CAVILOCK CL400 Magnetic Bi-Parting ADA Kurulum Talimatları
İç Mekan Mobilyaları Cavity Sliders CAVILOCK CL400 Magnetic Bi-Parting ADA için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Cavity Sliders CAVILOCK CL400 Magnetic Bi-Parting ADA 2 sayfaları.
Sayfayı Yazdır
Installation Instructions
for CL400 Magnetic
Bi-Parting ADA Privacy
Handles
Before you Start:
1.
These handles have been manufactured to specifications which cannot be altered by the
installer. These include:
a Handle type: the CL400 ADA handle is available in Passage, Privacy and Bi-Parting versions. You
have purchased the Bi-Parting Privacy version.
b Configuration: the Privacy handle configurations include; Snib/Snib, Snib One Side and Snib/Emergency.
c Door thickness range: There are four different door thickness ranges: 34-40mm, 40-46mm,
46-52mm and 52-58mm (1-3/8" to 1-9/16", 1-5/8" to 1-3/4", 1-13/16" to 2" and 2-1/16" to 2-1/4").
Handles for thicker doors are available on request.
d Security: the CL400 handle varies in security depending on the version and configuration. The
CL400 ADA Bi-Parting Privacy configuration provides low level security. It is important to note
that the CL400 handle should not be installed in situations where a high level of security is
required, e.g. external entry points or high security internal doorways.
Refer to the information printed on the Side Handle and Chassis boxes to ensure you have
purchased handles with the correct specifications for your situation. If the specifications are
incorrect you will need to exchange the handles.
2.
Component drawings have been provided. Please familiarise yourself with the components and
check the package to ensure nothing is missing. Note: Components may vary slightly between
configurations.
3.
To ensure the handles latch accurately, it is essential that both doors are adjusted for height and
are parallel with each other when closed before installing the handles.
4.
The CL400 is a metric handle. Accurate measurements are shown in millimetres. Conversions to
inches are approximate.
5.
NZS4121:2001: To comply with NZS4121:2001 the centre of the handles should be positioned between
900mm and 1200mm (1000mm optimal) above finished floor level. There must be a minimum clear
walk through of 760mm (Aust. 850mm). There must be a 45mm clear space from edge of pull handle
to door jamb when the doors are fully open. The supplied 'Down to Lock' label must be positioned as
close as possible to the locking handle. Consult local standards for guidelines relating to the specific
project.
USA ADA (American Disabilities Act) Guidelines: Handle should be positioned between 34 - 48"
above finished floor level. Allow a minimum of four inches for the protrusion of the door in the
open position. This can be achieved by using track stops or blocking in the back of the pocket.
Consult local standards for guidelines relating to the specific project.
Door Preparation
1
. Mark a line on the face of the doors where
the centre of the handles are to be positioned.
Align the centre line on the door cut out
template with the centre line on the door.
Follow the instructions on the template.
Repeat cut out for both doors.
Door face
Door face
Transfer
lines
across
front
edge of
doors
Door
cut out
template
2
. Mark two holes in the centre of the door
thickness in the positions shown. Using these
marks, drill two 2.5mm (3/32") diameter holes
to a depth of 35mm (1-3/8").
Repeat holes for both doors.
5mm
(13/64")
Ø 2.5mm
(3/32")
Door
thickness
5mm
(13/64")
Fitting the Bi-Parting Mate
3
. The Bi-Parting chassis contains a
strong magnet. Read the warning on
page 2 before continuing.
Remove the Bi-Parting chassis from its
packaging. Remove the face plate screw
and face plate from the chassis.
Align the chassis with the centre of the door
thickness. Screw the chassis to the door (using
the two chassis mounting screws) through
1
the slotted holes at the top and bottom of the
chassis. DO NOT fully tighten the screws.
Realign the chassis with the centre of the
door thickness. When happy with the chassis
position, fully tighten the screws.
Centre of door
thickness
Chassis
mounting
screws
Slotted hole
Magnet
=
✓
Correct alignment
4
. Fit the 6x side handle to chassis screws.
Leave a 3mm gap (1/8") between the underside
of the screw head and the chassis.
2
3mm (1/8") gap
under head
Side handle
to chassis
screws
1
Component Drawings - Bi-Parting Mate
Straight handle option shown.
Bi-Parting Side Handle Box
a
Bi-Parting Side Handle (Left)
b
Bi-Parting Side Handle (Right)
Bi-Parting Chassis Box
c
Bi-Parting Face Plate
d
Bi-Parting Chassis
e
Magnet
Chassis Mounting Screws (2)
f
g
Side Handle to Chassis Screws (6)
h
Face Plate Screws (3)
i
Handle Joining Screws (2)
Tools
(contained in Bi-Parting Chassis Box)
j
CL400 Allen Key
WARNING: THE BI-PARTING CHASSIS CONTAINS A STRONG MAGNET
IRON FILINGS - Magnets will attract shavings from iron or ferrous metals which may be
hard to remove. Keep magnets a safe distance away from these materials.
DANGER FOR CHILDREN - Magnets may cause serious injury if swallowed. Keep out of reach of
children.
CRUSHING, BLISTERS AND CUTS - Fingers may become caught between magnets resulting in
crushing, blisters or cuts.
BREAKING OR CHIPPING - It is possible that magnets could chip or shatter on contact with other
hard materials, resulting in chips flying off at high speed into someone's eye. Chips can also be
very sharp - treat them as you would broken glass.
MAGNETICALLY SENSITIVE ITEMS - Keep a safe distance between the magnet and all objects
that can be damaged by magnetism (e.g. mechanical watches, pacemakers, cell phones etc.).
DISPOSAL - Magnets should be disposed of carefully and in accordance with your local regulations.
3
Fitting the Bi-Parting Mate
5
. Select the Bi-Parting side handle that has
no visible fasteners (see diagram 5).
Fit it to the chassis by sliding the front flange
of the handle under the heads of the 3x side
handle to chassis screws. Tighten the screws.
3
=
Front flange
6
. Fit the remaining Bi-Parting side handle to
the chassis and tighten the 3x side handle to
chassis screws.
4
IMPORTANT: Install THIS handle FIRST
a
i
f
h
(3)
e
g
(6)
c
7
. Use the ball end of the CL400 Allen key
to tighten the 2x handle joining screws.
Use the other end of the Allen key to
firmly tighten the screws.
5
No
visible
screws
here
8
. Fit the Bi-Parting face plate to the chassis
using the 3x face plate screws.
6
Go to page
2
d
(2)
b
j
4
7
M3.5
handle
joining
screws
CL400
Allen key
Bi-Parting
8
face plate
Face
plate
screws
5
(overleaf)