Datalogic OM-GRYPHON Hızlı Referans Kılavuzu - Sayfa 2
Barkod okuyucu Datalogic OM-GRYPHON için çevrimiçi göz atın veya pdf Hızlı Referans Kılavuzu indirin. Datalogic OM-GRYPHON 2 sayfaları.
Sayfayı Yazdır
DEFAULT VALUES
USB-KBD DEFAULT SETTINGS
USA keyboard, FIFO enabled, inter-character and inter-code delays disabled,
USB keyboard speed normal.
: code identifier disabled, code length not transmitted, no header,
DATA FORMAT
terminator = ENTER, character replacement disabled, address stamping
disabled, address delimiter disabled.
RS232 Standard DEFAULT SETTINGS
9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, inter-character delay
disabled, rx timeout 5 sec., ACK/NACK disabled, FIFO enabled, serial trigger lock
disabled.
: code identifier disabled, code length not transmitted, no header,
DATA FORMAT
terminator = CR-LF, character replacement disabled, address stamping
disabled, address delimiter disabled.
WEDGE DEFAULT SETTINGS
USA keyboard, caps lock off, caps lock auto-recognition enabled, num lock
unchanged, inter-character and inter-code delays disabled.
: code identifier disabled, code length not transmitted, no header,
DATA FORMAT
terminator = ENTER, character replacement disabled, address stamping
disabled, address delimiter disabled.
PEN DEFAULT SETTINGS
Interpret operating mode, minimum output pulse 600 μs, conversion to Code
39, overflow medium, output level normal, idle level normal, inter-block delay
disabled.
RADIO PARAMETERS
battery type NiMh
TECHNICAL FEATURES
OM-GRYPHON™
Electrical Features
Supply voltage
9..28 Vdc
Power consumption
max. 8 W (charging) *
LED Indicators
Battery charging red,
Charge completed green, Power / Data yellow
Time of recharge
From 3 to 5 hours
Radio Features
European Models
USA Models
Working Frequency
433.92 MHz
910 MHz
Bit rate
19200 baud
36800 baud
Range (in open air)
30 m
15 m
RF Modulation
FSK
Max number of devices per
16
base station
Max number of devices in
2000
the same reading area
Environmental Features
Working temperature
0° to +40 °C / 32° to 104 °F
Storage temperature
-20° to +70 °C / - 4° to 158 °F
Humidity
90 % non condensing
Protection class
IP30
Mechanical Features
Weight
about 250 g / 8.81 oz
Dimensions
208 x 107 x 55.5 mm / 8.1 x 4.2 x 2.18 in
Material
ABS
*
Having a switching regulator inside, the OM-Gryphon™ draws the same
power, regardless of the supply voltage, i.e. as the input voltage increases the
current drawn decreases.
RESTORE DEFAULT
RESTORE OM-GRYPHON™ DEFAULT
Ì$+RX0$-qÎ
To change the defaults refer to the Gryphon™ Dx30/Mx30 Reference Manual, part
number 90ACC1930, or to the Configuration program, both downloadable from the
website.
INTERFACE SELECTION
Select one of the interface codes according to your application.
USB INTERFACE SELECTION
USB-KBD
Ì$+UA03$-:Î
USB-KBD-ALT-MODE
Ì$+UA04$-@Î
USB-COM*
Ì$+UA02$-4Î
USB-IBM-Hand Held
Ì$+UA01$-.Î
* When configuring USB-COM, the relevant files and drivers must be installed
from the USB Device Installation software, which can be downloaded from the
web site http://www.scanning.datalogic.com.
PEN EMULATION INTERFACE SELECTION
PEN
Ì$+CP6$-BÎ
RS232 INTERFACE SELECTION
RS232 Standard
Ì$+CP0$-$Î
Nixdorf Mode A
Ì$+CM2EC0$->Î
Fujitsu
Ì$+CM1$-ÈÎ
ICL Mode
Ì$+CM0$-ÃÎ
WEDGE INTERFACE SELECTION
Wedge IBM AT or PS/2 PCs
Ì$+CP500$-aÎ
PC Notebook
Ì$+CP505$-ÈÎ
PC Notebook - ALT mode
Ì$+CP508$-2Î
IBM AT - ALT mode
Ì$+CP507$-+Î
Many other interfaces are supported and can be selected from the Gryphon™
Dx30/Mx30
Reference
Manual
available
online
at
http://www.scanning.
datalogic.com. Other supported interfaces:
USB: USB-IBM-Table Top; USB-KBD-APPLE
WEDGE: IBM XT; IBM SURE1; IBM Terminal 3153; IBM Terminals 31xx, 32xx,
34xx, 37xx; Wyse Terminals ANSI – PC –ASCII – VT220 style Keyboards; Digital
Terminal VT2xx/VT3xx/VT4xx; APPLE ADB Bus
KEYBOARD NATIONALITY
USB-KBD and Wedge users should select one of the following wedge keyboard
nationality codes according to your keyboard.
Belge
Ì$+FJ7$-8Î
Deutsch
Ì$+FJ3$-$Î
English
Ì$+FJ4$-)Î
Español
Ì$+FJ6$-3Î
Français
Ì$+FJ2$-ÊÎ
Italiano
Ì$+FJ1$-ÅÎ
Japanese
Ì$+FJ8$-=Î
Svenskt
Ì$+FJ5$-.Î
USA (Default)
Ì$+FJ0$-|Î
DATA FORMAT TERMINATORS
For your convenience, some common Terminators are given below. For other
Header/Terminator selections, Data Format and Advanced Data Format
parameters, see the Gryphon™ Dx30/Mx30 Reference Manual.
CR-LF
Ì$+EA120D0A$-ÃÎ
Enter
Ì$+EA1183$-0Î
Tab
Ì$+EA1184$-8Î
None
Ì$+EA10$-dÎ
OPERATING TEST
Read the TEST code below.
Code 128
t
e
s
t
USING OM-GRYPHON™ RADIO CRADLE
The OM-Gryphon™ cradle, paired with one Gryphon™ M series reader, builds a
Cordless Reading System for the collection, decoding and transmission of
barcoded data.
OM-Gryphon™ can be connected to a Host PC through a USB, RS232, Wedge or
Pen emulation cable. All models are suited for single-cradle layouts.
The LEDs signal the OM-Gryphon™ status, as described in the following table:
LED
STATUS
Yellow On = OM-Gryphon™ is powered.
Power on /
Yellow Blinking = OM-Gryphon™ receives data and
Data
commands from the Host or the reader.
Red On = the battery charge is in progress.
Charging
Red Blinking = the battery reconditioning is in progress.
Charge
Green On = the battery is completely charged.
completed
Charging +
Red and Green Blinking together = the reader is not
Charge
correctly placed onto the cradle.
completed
Reconditioning
battery button
Charging
(red LED)
Power on / Data
Charge completed
(yellow LED)
(green LED)
To setup your OM-Gryphon™ cradle you must:
1.
Make all system connections.
2.
Configure the OM-Gryphon™ cradle.
BATTERY SELECTION
Battery selection is required only when the Gryphon™ M reader has an Alkaline
battery and you want to use OM-Gryphon™ either for serial configuration, software
upgrades or to hold Gryphon™ M. Since this type of battery must not be charged it
is necessary to disable the OM-Gryphon™ charge function by following the
procedure:
1.
With the Gryphon™ M read the following code:
Alkaline
Ì$+RN4$-]Î
The green LED on the Gryphon™ M will blink, signaling the reader has
accepted the command.
2.
Place the reader onto the cradle within 10 seconds. The green LED
turns off and a short beep is emitted.
To enable the charge function repeat step 1 and 2 substituting the "Alkaline" code
with the following one:
NiMh
Ì$+RN6$-gÎ
Attempts to charge Alkaline batteries could cause leakage of
liquid, generation of heat or, in extreme cases, explosion. If
using Alkaline batteries, carefully follow the procedure above
to avoid damage.
CAUTION