elsner elektronik KNX PY Teknik Özellikler ve Kurulum Talimatları - Sayfa 2

Ölçüm Cihazları elsner elektronik KNX PY için çevrimiçi göz atın veya pdf Teknik Özellikler ve Kurulum Talimatları indirin. elsner elektronik KNX PY 2 sayfaları. Pyranometer

Sayfayı Yazdır

Fig. 8

Different mounting arms are available

from Elsner Elektronik as additional, op-

tional accessories for flexible installation

of the weather station on a wall, pole or

beam (pictures of sensors exemplary).

Example of the use of a mounting arm:

Due to flexible ball joints, the sensor can

be brought into ideal position.

Fig. 9

Example use of the hinge arm mounting:

With the hinge arm mounting, the weat-

her station projects from beneath the

roof overhang. Sun, wind and precipita-

tion can act upon the sensors without

hindrance.

Fig. 10

Example use of the hinge arm mounting:

Fitting to a pole with worm drive hose

clips

2.2.2. View of rear side and drill hole plan

Fig. 11 a+b

Drill hole plan

Dimensions of rear side of housing with bra-

cket. Subject to change for technical enhan-

cement.

2.2.3. Preparing the sensor

Unsnap cover

and remove upwards

Fig. 12

1 Cover snaps

2 Bottom part of housing

The sensor cover snaps in on the left and right along the bottom edge (see Fig.).

Remove the cover.

Push the connection cable through the rubber seal on the bottom of the device and

connect voltage and data cable to the provided clamps.

Pyranometer KNX PY • Version: 31.01.2023 • Technical changes and errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de • Technical Service: +49 (0) 7033 / 30945-250

Pyranometer KNX PY

Langloch 7,5 x 5 mm

2.2.4. PCB layout

2.2.5. Mounting the sensor

Close the housing by putting the cover back over the bottom part. The cover must

snap in on the left and right with a definite "click".

Fastening

To remove it, the sensor can be simply pulled upwards out of the mount, against the

resistance of the fastening.

2.3. Notes on mounting and commissioning

Do not open the device if water (rain) might ingress: even some drops might dama-

ge the electronic system.

After the bus voltage has been applied, the device will enter an initialisation phase

lasting a few seconds. During this phase no information can be received or sent via

the bus.

Addressing of the device at the bus

The device is supplied with the bus address 15.15.250. You can program another ad-

dress into the ETS by overwriting the 15.15.250 address or by teaching via the pro-

gramming key on the circuit board inside the housing.

Maintenance

WARNING!

Risk of injury caused by components moved automatically!

The automatic control can start system components and place people in

danger.

•

Always isolate the device from the mains for servicing and cleaning.

The device must regularly be checked for dirt twice a year and cleaned if necessary.

In case of severe dirt, the sensor may not work properly anymore.

ATTENTION

The device can be damaged if water penetrates the housing.

•

Do not clean with high pressure cleaners or steam jets.

Disposal

After use, the device must be disposed of in accordance with the legal regulations.

Do not dispose of it with the household waste!

Fig. 13

1 KNX clamp +/-

2 Programming LED

3 Programming pushbutton

for the teach-in of the de-

vice

Fig. 14

Make sure the cover and bottom part

are properly snapped together! This

picture is looking at the closed sensor

from underneath.

Fig. 15

Push the housing from above into the

fastened mount. The bumps on the

mount must snap into the rails in the

housing.