Datalogic S5N-PA U Series Kullanım Kılavuzu

Aksesuarlar Datalogic S5N-PA U Series için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Datalogic S5N-PA U Series 7 sayfaları. Luminescence sensor

Sayfayı Yazdır

Datalogic S5N-PA U Series Kullanım Kılavuzu

This product is covered by one or m ore of the following patents.

European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.

Italian Patent IT 1,321,772.

S5N-PA/MA...U

Luminescence sensor

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED

The yellow LED ON indicates that the N.O. (normally open) output status

is closed.

READY/ERROR LED (bicolour)

When the bicoloured LED is continuously green, the sensor is operating

in a normal condition and it is ready to function correctly (stability

condition).

The red and green blinking of the LED indicates a wrong sensor setting.

Please refer to the "SETTING" paragraph to get the correct setting

procedure.

SET PUSHBUTTON

A long pressure on the pushbutton activates the self-setting procedure.

INSTALLATION

S5N-PA...U: The sensor can be fixed by means of the M18x1 threaded

body through a  18 mm hole, using the specific washer and the

enclosed 24 mm nuts (maximum torque of tightening 1.5 Nm).

Alternatively, the sensor can be mounted through the two housing's holes

using two screws (M3x22 or longer) and nuts.

Amongst the various possible solutions, we suggest to choose the

combination that offers the best visibility of the signalling LEDs and the

easiest access to the SET pushbutton.

22 mm nuts, h=8 mm, (2 Nm maximum tightening torque) are available to

guarantee an improved torque.

S5N-MA...U: The sensor can be fixed by means of the M18x1 threaded

body through a  18 mm hole, using the specific washer and the two

CH.24 nuts enclosed (22 Nm maximum tightening torque).

For both plastic version and metallic version are available various

orientable fixing brackets to ease the sensor positioning (please refer to

the accessories listed in the general catalogue).

10...15°

The operating distance is measured

from the front surface of the sensor

lens.



To detect luminescent marks on

reflective

surfaces,

position the

sensor axis at 10°...15° respect to

the orthogonal line of the surface to

detect.

The connections are compliant to the EN 60947-5-2 standard.

BROWN

WHITE

BLACK

BLUE

S5N-PA VERSIONS

S50-PA VERSIONS

81.5

1.5

3.5

2.5

SET PUSHBUTTON

N°.2 Ø3.8

OUTPUT LED

Power supply:

Ripple:

Current consumption

(output current excluded):

Outputs:

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Indicators:

Setting:

Operating mode:

Data retention:

Operating temperature:

Storage temperature:

Insulating strength:

Insulating resistance:

Operating distance (typical

values):

Minimum spot dimension:

Emission type:

Ambient light rejection:

Vibrations:

Shock resistance:

10...15°

Housing material:

Lens material:

Mechanical protection:

Connections:

→

Weight:

AtEx 2014/34/EU

CONNECTIONS

M12 CONNECTOR

10 ... 30 Vdc

N.C. OUTPUT

(WHITE)

0 V

N.O. OUTPUT

(BLUE)

0 V

DIMENSIONS

S50-MA VERSIONS

14.5

S5N-MA VERSIONS

CABLE VERSION

2.5

READY/ERROR LED

OUTPUT LED

TECHNICAL DATA

S5N-PA PLASTIC VERSIONS

10 ... 30 Vdc (limit values)

2 Vpp max.

25 mA max.

N.O. and N.C.; PNP or NPN (short-circuit protection)

100 mA max.

2 V max.

500  s

1 kHz

OUT PUT LED (YELLOW) / READY/ERROR LED (GREEN/RED)

SET pushbutton

LIGHT mode on N.O. output / DARK mode on N.C. output

non volatile EEPROM memory

-10 ... 55 °C

-20 ... 70 °C

500 Vac 1 min., between electronics and housing

>20 M 500 Vdc, between electronics and housing

8...20mm range, maximum signal at 10 mm

3 mm

LED UV (370 nm)

according to EN 60947-5-2

0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

PBT

PMMA

IP67 Metal versions type 1 enclosure

2 m cable  4 mm / M12 - 4 pole connector

75 g. max. cable vers.

25 g. max. connector vers.

II 3D EX tc IIIC IP67 T 85°C

The supplied sensor is set at the maximum sensitivity, allowing

the detection of the minimum luminescence intensity. No other

setting procedure is necessary, unless luminescent objects placed

on luminescence backgrounds have to be detected.

EASY TOUCH

10 ... 30 Vdc

The sensor uses the patent-covered EASY TOUCH technology that

allows a rapid and safe self-setting of the product.

(BROWN)

Two different setting possibilities are available:

- EASY TOUCH

N.O. OUTPUT

(BLACK)

setting.

- FINE DETECTION; to be used only in particularly critical conditions,

this setting procedure is used only when the EASY TOUCH is not

sufficient.

Setting of S5N-PA/MA...U

To achieve a correct sensor functioning, the luminescence mark or

object to be detected has to be placed at the right reading distance.

- EASY TOUCH

14.5

The EASY TOUCH technology allows the functioning in the LIGHT

mode (mark presents a higher luminescence respect to the

background).

The mark to detect has to be placed correctly at the right reading

distance within the sensor spot.

Press the SET pushbutton until the READY/ERROR LED turns OFF.

Release the SET pushbutton and wait for the READY/ERROR LED to

CABLE VERSION

turn green.

The sensor is now ready to detect the pre-set luminescent mark or

SET PUSHBUTTON

object (output LED turns ON when the NO output is closed).

Note: The automatic EASY TOUCH setting has to be performed

without any objects inside the sensor reading range (or using a non-

luminescent object) in order to bring the sensor back to the maximum

READY/ERROR LED

sensitivity condition.

OUTPUT LED

- Fine detection (DARK or LIGHT m ode)

This mode offers an improved detection precision and aIso allows the

detection of luminescent marks or objects placed on luminescent

backgrounds.

S5N-MA METALLIC VERSIONS

The operating mode is selected automatically by the sensor:

DARK operating mode (mark presents a lower luminescence respect

to the background) or LIGHT operating mode (mark presents a higher

luminescence respect to the background).

The mark to detect has to be placed correctly at the right reading

distance within the sensor spot.

Press the SET pushbutton. The READY/ERROR LED turns OFF.

Keep the SET pushbutton pressed until the READY/ERROR LED

blinks green. Place the background under the sensor spot.

Press the SET pushbutton again until the READY/ERROR LED turns

OFF. The sensor is now ready to detect, with a very high precision, the

pre-set luminescent mark (output LED turns ON, READY/ERROR

LED turns green).

Datalogic S.r.l.

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy

Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

Helpful links at www.datalogic.com: Contact Us, Terms and Conditions, Support.

Nickel plated brass

110 g. max. cable vers.

limiting the rights under copyright, no part of this documentation may be reproduced, stored in

or introduced into a retrieval system, or transmitted in any form or by any means, or for any

60 g. max. connector vers.

purpose, without the express written permission of Datalogic S.p.A. and/or its affiliates.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many

countries, including the U.S.A. and the E.U. All other trademarks and brands are property of

their respective owners. Datalogic reserves the right to make modifications and improvements

without prior notification.

SETTING



; a long pressure of the SET pushbutton allows self-



(standard detection in the LIGHT m ode)

For information about the disposal of Waste Electrical and Electronic

Equipment (WEEE), please refer to the website at www.datalogic.com.

821006252 Rev.C