Datalogic Lynx D Kullanıcı Kılavuzu
PDA Datalogic Lynx D için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Datalogic Lynx D 2 sayfaları. Single slot dock
Ayrıca Datalogic Lynx D için: Hızlı Başlangıç Kılavuzu (2 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar)
Sayfayı Yazdır
Lynx™ Four Slot Dock
Read this manual carefully before performing any
type of connection from the terminal to a host PC
using the Four Slot Dock.
The user is responsible for any damages caused
NOTE
by incorrect use of the equipment or by
inobservance of the indication supplied in this
manual.
The Four Slot Dock paired with a Lynx PDA builds a reading
system for the collection, decoding and transmission of barcode
data.
The Four Slot Dock can charge both the terminals and the spare
batteries at the same time. The spare batteries (both standard
capacity
battery
94ACC0064
and
high
capacity
94ACC0065) can be charged by inserting them into the slots at
the back of the cradle.
The Four Slot Dock comes in two different models, the Charger
(94A150037) and the Ethernet (94A150054).
The Ethernet model also provides Ethernet connection for data
transfer via local area networks.
A
B
F
C
E
D
Figure 1 –Four Slot Dock
Key:
A) Link LED for Ethernet Port 1,2,3,4
B) Battery charger LED for Slot 1,2,3,4
C) Power supply connector
D) Ethernet Port 1 (with integrated Link and Speed LEDs)
E) Ethernet Port 2 (with integrated Link and Speed LEDs)**
F)
Power on LED
822001291
Used in the Ethernet Four Slot Dock only
Available in the Ethernet Four Slot Dock only
PDA INSERTION/ REMOVAL
For correct insertion into the cradle, insert the mobile computer
from the top of the cradle and push it down.
To remove the mobile computer from the cradle, simply pull it
upwards while holding the cradle firmly down.
battery
Figure 2 - PDA Insertion
Power Supply
Each 4SD requires a power supply to be connected to mobile
computers. We recommend the power supply already included in
the box.
-
+
Figure 3 - Power Supply Polarity
LED INDICATORS
Power LED Status Indicator (F)
Color
Status
Green
Cradle powered
Battery Charging LED Status Indicators (B)
Color
Status
Off
Battery absent
Red
Battery charge in progress
Green
Charge completed
Red Blinking
Error
USING THE SPARE BATTERY CHARGER
Insert the battery, contacts side first, into the slot and press it
until the battery latch is automatically closed; charging starts
automatically.
Figure 4 - Spare Battery Insertion
To remove the battery, press the battery-release lever.
Figure 5 - Spare Battery Removal
ETHERNET CONNECTION
The Ethernet cradle drivers are pre-installed on the Lynx and
initiate automatically when the terminal is placed in a properly
connected Four Slot Dock Ethernet.
When the PDA is inserted into the Four Slot Dock Ethernet, the
connectivity icon on the taskbar indicates that the mobile
computer is connected to a network.
The maximum bandwidth capacity for each
Mobile Computer is 12Mbps.
NOTE
The yellow Link LED blinks to indicate activity, or stays lit to
indicate that a link is established. When it is not lit it indicates that
there is no link.
Connections should always be made with power
OFF!
CAUTION
How to connect
Connect the Ethernet cradle (Ethernet port 1 - E) to an Ethernet hub
or to a port on the host device. Connect the Ethernet cradle (power
port - F) to the power supply.
A
F
E
B
C
Figure 6 - Ethernet Connection
Key:
A) Ethernet 4 Slot Dock
B) Power supply without power cord, supplied with the 4SD and
country specific power cord
C) UTP CAT 5E cable (recommended use)
D) Ethernet hub
E) Ethernet port 1
F)
Power port
Available in the Ethernet Four Slot Dock only
D