Dataprobe iBoot-G2 Hızlı Başlangıç Kılavuzu - Sayfa 2
Anahtar Dataprobe iBoot-G2 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Dataprobe iBoot-G2 3 sayfaları.
Sayfayı Yazdır
Changing the IP Address
1. Device
Management
Management Utility (DMU) from Dataprobe's website at
dataprobe.com/support/iboot.
means to find and configure your iBoot-G2 for use.
discover all the iBoots on your network, display the current IP
address of each, and allow setting of any valid IP address.
Note:
The IP address can only be set within the first two
minutes of powering up the iBoot. The Setup Utility will only
work with iBoots on the same local subnets as the PC.
The iBoot-G2 Setup Utility can also be used to return an iBoot-
G2 to its Factory Default condition. This can be used to recover
an iBoot-G2 with a lost password. Highlight an iBoot-G2 from
the display and click Factory Defaults. This must also be done
within the first two minutes of powering up the iBoot.
Complete instructions for the DMU are provided with the
download, and in the full iBoot-G2 Manual.
2. Web Page Setup
then Network. Enter the new IP Address, Subnet Mask and
Gateway, then click Save. Click the Reboot button (or press the
reset button next to the power outlet LED) to restart the iBoot-
G2 with the new settings.
3. DHCP
From the Home page, click on Setup, then Network.
Change the IP Mode from Static to DHCP. Click Save, then
Reboot. The iBoot-G2 will obtain its network settings from the
server. Check the server, or use the Device Management Utility
to obtain the new settings.
When using this product, basic safety precautions should always be followed to reduce the risk of fire,
1.
Read and understand all instructions.
2.
Follow all warnings and marked on the product.
3.
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4.
Do not use this product in an outdoor environment or near water, for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
5.
Do not place this product on an unstable cart, stand, or table. The product
may fall, causing serious damage to the product.
6.
Slots and openings in this product and the back or bottom are provided for
ventilation to protect it from overheating; these openings must not be
blocked or covered. The openings should never be blocked by placing the
product on the bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register. This product
should not be placed in a built-in installation unless proper ventilation is
provided.
7.
This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your dealer or local power company.
8.
This product is equipped with a three wire grounding type plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding type
power outlet. This is a safety feature. If you are unable to insert the plug
into the outlet, contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the grounding type plug. Do not use a 3-
to-2 prong adapter at the receptacle; use of this type adapter may result in
risk of electrical shock and/or damage to this product.
9.
Do not allow anything to rest on the power cord. Do not locate this product
where the cord will be abused by persons walking on it.
Utility
Obtain
the
The DMU provides the easiest
From the home page, click on Setup,
Important Safety Instructions
electric shock, and injury to persons, including the following:
Device
It can
Fig. 5 Device Management Utility
Fig. 6 Network Setup Page
10. Do not overload wall outlets and extension cords as this can result in the
risk of fire or electric shock.
11. Never push objects of any kind into this product through slots as they may
touch dangerous voltage points or short out parts that could result in a risk
of fire or electrical shock. Never spill liquid of any kind on the product.
12. To reduce the risk of electrical shock, do not disassemble this product, but
take it to a qualified serviceman when some service or repair work is
required.
Opening or removing covers may expose you to dangerous
voltages or other risks. Incorrect re-assembly can cause electric shock
when the appliance is subsequently used.
13. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a) When the power supply cord or plug is damaged or frayed.
b) If liquid has been spilled into the product.
c)
If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating
instructions.
operating instructions because improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the product to normal operation.
e) If the product has been dropped or has been damaged.
f)
If the product exhibits a distinct change in performance.
14. Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
15. Do not use the telephone to report a gas leak in the vicinity of the leak.
16. Do not exceed the maximum output rating of the auxiliary power receptacle.
Adjust only those controls that are covered by the