Frigicoll MDL-PSM28W Kullanıcı El Kitabı - Sayfa 3

Hava Temizleyici Frigicoll MDL-PSM28W için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Frigicoll MDL-PSM28W 6 sayfaları. Pco-kit

Sayfayı Yazdır

Overview

Basic feature: IP20

Suitable for air-conditioning duct.

Technical Parameters:

Model

MDL-PSM10W

Power(W)

AC Source

Rated Current (A)

0.05

Product Size

250*157*(72+227)

L*W*(h1+h2)(mm)

Airflow(m

/h)

<1500

Safety Precautions

To prevent accidents such as damage, fall, electric shock and fire, which may

cause personal injury, please install and use the PCO-kit in strict accordance with

the instructions.The PCO-kit is not replaceable by the user. Do not alter the UV-C

tube or replace the components!

The power supply must be within the rated voltage.

(If the PCO-kit works at voltages outside of range for a long time, it may be

damaged.)

Ask a specialized technician to check or repair the PCO-kit.

(Operations performed by a non-professional staff may cause danger.)

In case of exception, cut off the power supply immediately and contact the sales

store.(Provide the model for maintenance. Refer to the label attached to the

control box.)

The external flexible cable or cord of this device are not replaceable. The PCO-

kit would be discarded if flexible cable or cord are damaged.

When installing PCO-kit, it should not be too close to the air outlet.

(Too close to the air outlet, the ultraviolet rays of the PCO-kit may cause harm

to people, animals or plants.)

UV-C tubes are hazardous materials, do not discard them at will; please handle

them according to the recycling management of hazardous materials.

Do not look directly at the pco-kit when the UV-C lamp is working.

The pco-kit installation position is more than 1.5 meters away from the air outlet.

The cable between the signal port and the controller should not exceed 3 meters.

Fibre-duct need metal support (from local market) inside duct and reserve

inspection hole on duct bottom.

MDL-PSM18W

MDL-PSM28W

220-240V~ 50/60Hz

0.095

0.16

250*157*(72+371)

250*157*(72+565)

<2600

<4300

Main Components Name

① Power Swicth Key

② Digital Tube

③ Set Button

Main Components Function

1. Digital tube display:

(1) Display "U1" or "U2", U1 mode is a stand-alone mode,U2 mode is a multi

-machine mode.When the PCO-kit is powered on, or when the "Set" key is

pressed, U1 or U2 are displayed.

(2) When the PCO-kit works normally, the life of the UV lamp is displayed.

(3) Error code display. When the PCO-kit fails, the fault code and life time will be

displayed in turns at 3S intervals.

2. Set button:

1) Switch working modes U1 and U2.

2) When the service life of the UVC-tube ends, long press(about 5s) this button to

reset to the default value of 8000 hours.

3. Alarm port (1,2): PCO-kit outputs an abnormal output signal to the control panel

to remind the user that the product is abnormal.

4. Control port ( 3, 4): The user can control the "running" and "stop" states of

PCO-kit on the control panel interface. When the PCO-kit is turned on, it will

start to work after 5s, if the air duct is windy; when there is no wind in the air

duct, the PCO-kit will not work.

Fault Code

Wind sensor failure.

UV-C tube is not bright or the photoresistor is damaged.

There is light detected when the UV-C tube is not turned on.

The photoresistor is damaged or the structure has light leakage.

Ballast failure.

End of life of UV-C tube.

④ Signal Line Port

(Alarm Port &Control Port)

⑤ Power Cable

Description