Aussievan Easy Tune BD-11DX Hızlı Başlangıç Kılavuzu - Sayfa 4

TV Anteni Aussievan Easy Tune BD-11DX için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Aussievan Easy Tune BD-11DX 9 sayfaları. Remote controlled tv antenna

Sayfayı Yazdır

Outdoor - Installation

Locate a suitable location on the external caravan wall and permanently install the supplied

brackets as suggested in Fig 1. Assemble the antenna as illustrated. Make sure the yoke at the

top of the telescopic mast is seated properly into the groves by rotating with a gentle downward

force. Secure the antenna head to the yoke by tightening the hand screws about ¾ turn after

making contact with the yoke. Make sure there is about a forearm (40cm) length of slack

coaxial cable for rotation. Screw on the coaxial cable to the antenna by hand firmly, do not over

tighten. The outdoor unit has two pairs of telescopic dipoles which can be extended for

improving VHF reception. For reception of only UHF or Digital signals, the telescopic dipoles

can remain retracted. Adjust the telescopic mast to the desired height by loosening the screw

locking rings. Tighten the locking rings once the desired height is reached. With the complete

antenna assembly align the bottom of the telescopic mast with the lower mast bracket at a

slanting angle, then push the mast body in to the top clamp bracket and secure by gently

tightening the hand screw. Do not force. Mast will be held in place securely even with hand

screw lightly tightened. Plug the antenna cable into the outside antenna wall connector (refer

compatibility section at the end of this manual) or straight into the back of the remote control

base unit marked ANTENNA through the caravan window or any suitable opening

(recommended). The outdoor installation is now complete. To uninstall, reverse the process.

Indoor – One time installation

Make sure the TV is switched OFF. Unplug existing TV antenna if any. With the supplied inter-

connecting coaxial cable, plug one end of the cable into the TV antenna input at the back of TV

and the other end to the back of the BD-11DX remote control base unit marked TV1 or TV2. If the

coaxial cable is plugged into the antenna wall connector, with the other supplied interconnecting

coaxial cable, plug one end of the cable into the back of the BD-11DX remote control base unit

marked ANTENNA and the other end to the internal caravan antenna wall connector. Without

plugging the power adaptor to a wall socket, plug the power adaptor output to the power jack of

the remote control base unit. Plug the power adaptor to a wall socket and switch on. A red LED

should come on in the remote control base unit window. Installation is now complete. An

optional inter-connecting coaxial cable is required for connection to a second TV.

Remote Control Unit

Install 2 x AAA batteries in the remote control unit (not supplied). Remove battery cover by

pulling the battery cover catch to release the battery cover. Make sure the batteries are installed

with the correct polarity. Replace battery cover. To operate, point the remote controller at the

base unit and press the "ROTATE" button on the remote controller. A green LED will come on

in the base unit window indicating command received. The remote control has a range of about

6 metres line of sight. The antenna can also be operated without the remote control by pressing

the oval switch on top of the base unit marked ROTATION.

Operating the BD-11DX Antenna

Upon arriving at a destination, the TV has to be re-tuned to the local channel frequencies (refer

TV instructions manual) Press the button on the remote controller or the ROTATION button on

top of the base unit while looking at the picture on the TV. Keep the button depressed until a

clearest picture is attained, release the button. The antenna rotating mechanism has a built in

safety stop feature. At full revolution the motor automatically reverses to prevent the coaxial

cable from wrapping around the mast or burning out of the rotation motor.

Do not use any power adaptor other than the one supplied with the set. Unpredictable

behaviour or irreparable damage to the base unit and antenna may result from use of unsuitable

power adaptor.

Vertical Polarized Signal Reception

Across Australia, majority of the main TV transmission stations are horizontally polarized. In

some country areas, usually between major wide coverage transmitters, a vertical polarized

repeating station will serve the overlapping areas. A customized vertical bracket has been