AUSTRALIAN MONITOR AM3002 Kullanım Kılavuzu - Sayfa 9

Amplifikatör AUSTRALIAN MONITOR AM3002 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. AUSTRALIAN MONITOR AM3002 20 sayfaları. Audio power amplifier
Ayrıca AUSTRALIAN MONITOR AM3002 için: Şartname (2 sayfalar)

Sayfayı Yazdır
Controls
& Connectors
9
Rear Panel
6. Balanced Input
A
female 3-pin
XL
type connector
is
provided
on
each
inpul:
Pin
1
=
Signal Ground;
Pin
2
= Hot
(non-inverting
orin
phase);
Pin
3 =
Cold
(inverting
orreverse
phase).
6a.Signal Strapping
A male
3-pin
XL
type connector is provided
and
wired in parallel with the female input XLR for
strapping
/
looping
signal
between
amplifiers.
7. SPEAKON
Output Connector
The NEUTRI
K
(NL4MP)
4way SPEAKON connector
is
provided
asthe
main
speakeroutputtermination.
This emerging standard
of
loudspeakerlo
amplifier
connection allows
access
to
both
channels
ofthe
amplifier via the one
connector
for
bi-amp
applications. Channel-A
is
conside
red
thedominar
channel
and
has
both
channelswired
to
the
Speakon
connector. See
lhe
installation section
of
this
manual
fordetailed information
on
Speakonwiring.
9.
Mains Circuit Breaker
A
"push
to reset'thermal acting circuit breaker
is
supplied
on
youramplifierproviding overall
protedion
of
your amplifier's power supply and
the
interconnecting
mains. The
breakerwill
isolatethe
"active" mains conductor in the event of a high
current inlernal fault
or in
continued overload
condilions.
The
breakerwillnot
be
ableto
be
reset
immediately
affer tripping.
A
cool down period of around 30
seconds
is
required before
the breaker will reset
back into
circuit.
lfthe breaker"trips" immediately
aftera
reset,lhen
a
fault
may have
developed
within
theamplifier.
10.
D.C. Rail Breakers
YourAll3OOZ
a
m
plifier
is
frtted
with
15
Ampthermal
acting circuit breakers
as
overload protection
for
the
output
stage of
youramplifier.
These breakers
are
in
series with
the
high
cunent
supply railsto
the
amplifie/s
output stage and
will
"trip"when:
1)
An intemal fault exists;
2)
There
is
a
sustained overload;
3)
There
is
a
sustained short circuit;
4)
There
is a
sustained
load
fault.
Front Panel lndication will result
if
one of the
conesponding Rail Breakers
is
to
'trip".
-
The VU meter will
lighl
up
fully
and
the positive
output Rail
LED
will
e)ilinguish
if the
positive
supply Rail Breaker "trips".
-The Fault lndicatorwilllight
up
and pulse
in
sync.
with the
programsourceif
the
negative
supply
Rail
Breaker "lrips".
Ta.Binding Post Outputs
Binding posts (banana jacks) are provided for
speaker output
termination wilh banana plugs or
barewire.
The
red post
is
used as
positiveandthe
black post is used as negative.
8.
Mains Lead
Youramplifierissupplied
with
a
heavy
duly mains
lead (power cord)
appropriately
rated
forthe mains
supply
voltage marked on the rear panel of your
amplifier.
The wires in
lhe
mains lead are coloured
in
accordance
with the
following code:
BROVITN
=
ACTIVE;
BLUE
=
NEUTRAL;
GREENANDYELLOW
=
EARTH.
!
CAUTION
!
Your amplifier must always
be
earthedl
Australian Monitor
/tu