4titude a4S Hızlı Kullanım Kılavuzu

Gıda Tasarrufu 4titude a4S için çevrimiçi göz atın veya pdf Hızlı Kullanım Kılavuzu indirin. 4titude a4S 2 sayfaları. Automatic heat sealer

Sayfayı Yazdır

Automatic Heat Sealer a4S

Note: This quick user guide is not a replacement for the a4S Operation Manual which must be read before using the heat sealer

for the first time. All users must know and observe all safety instructions as detailed in the operation manual.

Important!

Shipping Bracket

The a4S is shipped with a transportation bracket to prevent the plate shuttle moving during shipping. It is essential that this

bracket is removed before the unit is powered up for the first time.

Sensor Protection Screw

To protect the rear foil sensor during transportation, the a4S is shipped with a protective screw highlighted with a white washer,

inserted into the rear of the instrument. Before the unit is switched on, please make sure that the screw is removed from the

instrument and retained with the other transportation packaging.

Please also refer to the a4S Operation Manual.

Operation of the a4S Automatic Heat Sealer

1. Connect the power cord and turn on the device.

2. Place the seal roll, along with its holder, on the device

locating the ends of the Axle in either Seal Roll Support 1

or 2. The orientation of the seal roll should be as indicated

by the purple arrow.

3. Perform the seal roll loading procedure (Please refer

to the a4S Operational Manual, section 2.4 Seal Roll

Loading Procedure).

4. Perform the fine adjustment of the seal position (Please

refer to the a4S Operational Manual, section 2.5 Fine

Adjustment of the Seal Position).

5. Adjust sealing temperature and time settings (Please see

reverse page).

6. Place the plate to be sealed on the plate carrier, using

an appropriate adaptor if necessary (Please see section

Plate Adaptors).

7. The

icon will remain grey while the unit is heating

Seal

or cooling. Once the set temperature is reached, the icon

will turn green.

8. Sealing can then commence by touching

4titude Ltd. • The North Barn • Surrey Hills Business Park • Damphurst Lane • Wotton • Surrey • RH5 6QT

T: +44 (0)1306 884885 • F: +44 (0)1306 884886 • E: [email protected] • www.4ti.co.uk

4ti-FL-0010 Quick User Guide a4S Automatic Heat Sealer VA en1/0/25/07.2015 OP

Quick User Guide •

Seal Roll Support 1

(seal roll with large diameter)

Seal Roll Support 2

(seal roll with small diameter)

Seal

Version A

0116

14.4 mm

0116

14.4 mm

0120

26.54 mm

0120

26.54 mm

0136

41.20 mm

Plate Adaptors

0136

41.20 mm

Plate Type / Plate Height

96well PCR plates

0960

16.1 mm

0960

16.1 mm

0384

10.6 mm

384well PCR plates

0384

10.6 mm

1536well plates,

standard height plates

0116

4mm ‒ 20mm

14.4 mm

0116

14.4 mm

0120

Mid-height plates

26.54 mm

0120

26.54 mm

14mm ‒ 33mm

Deep well plates

0136

41.20 mm

0136

41.20 mm

34mm ‒ 53mm

41.20 mm

0960

16.1 mm

0960

16.1 mm

0384

10.6 mm

0384

Adaptor / Side of adaptor to use

Adaptor B

Side with 96 holes

Adaptor B

Side with 384 holes

Adaptor B

Side with 384 holes

Adaptor A

No adaptor needed