Dymo 2000 Kullanıcı Kılavuzu - Sayfa 2
Etiket makinesi Dymo 2000 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Dymo 2000 5 sayfaları. Electronic labelmaker
Sayfayı Yazdır
Introduction
The Dymo 2000 Electronic Labelmaker enables you to
create a wide variety of high quality self-adhesive labels
of up to 88 characters.
The Labelmaker uses 6mm (
or 19mm (
3
/
") wide tape cassettes in a number of label
4
colours. Labels are tab-cut for easy removal from the
backing tape.
Text can be printed horizontally or
in a variety of sizes and styles and can be left-justified,
right-justified or centred on the label.
Warranty Registration
Please complete the warranty registration card and
return it to your national customer service address
within seven days – see the warranty booklet for
details.
Power Supply
BATTERIES
A
• Undo catch
then open and lift away battery
A
compartment cover
• Insert five size AA alkaline or re-chargeable nickel-
cadmium batteries, observing the polarity markings
A
, and refit cover.
• Remove batteries (pull ribbon
is to be unused for some time.
AC ADAPTOR
• Connect the AC adaptor to socket
adaptor plug disconnects the supply from the
batteries.
• Unplug the AC adaptor from the Labelmaker before
disconnecting the mains power to the adaptor,
otherwise settings will be lost (see also ON/OFF
Changing the cassette
B
• Slide catch
as shown to open cassette door
– see page 2.
B
• Hold cassette
as shown and lift it straight up
and out.
• Ensure tape and ribbon
cassette and tape passes between guide posts before
installing as shown. If necessary, turn spool
clockwise to tighten ribbon.
• Check that cassette switch
type – see page 2. A notch in the cassette will fit over
the switch when it is set correctly.
• Insert cassette with tape and ribbon positioned as
shown between print head
C
• Push firmly
until cassette clicks into place.
Ensure tape and ribbon are positioned correctly.
1
/
"), 9mm (
3
/
"), 12mm (
4
8
– see page 2.
A
) if the Labelmaker
A
. Inserting the
B
are taut across mouth of
B
D
is set for the cassette
C
and pinch roller
The Display
1234567890123456
1
/
")
2
Shift on
Text size
The display shows:
• Up to 15 characters, plus the cursor, at one time.
• Function indicators – as shown above.
• The display will flash if you press an incorrect
key in a function sequence.
Function keys
ON/OFF
Switches the power on and off.
• Switches off automatically after two minutes if no keys
are pressed. The last label created will be retained and
displayed when next turned on. In addition, any stored
settings will be retained.
Note: If the batteries are removed for more than a few
seconds, all text and stored settings will be lost. When
power is restored, the display will show a flashing
cursor (no text) and the settings will be medium height
normal width text with
CAPITALS
• Press for all subsequent characters to be in UPPER
CASE (CAPITALS), as confirmed by the CAPS indicator
in the display.
• Press again to cancel and return to lower case.
).
SHIFT KEY
• Press and hold down
B
alphabet key to produce an UPPER CASE (CAPS)
character.
• For dual purpose keys, press and hold
produce the legend above the key.
• Pressing
characters.
DELETE
DEL
• Press to delete the character to the left of the cursor, or
to exit certain function key operations.
CLEAR TEXT
C
.
• Press to clear all the current text and cancel any fixed
length setting, but leave the text size and other
settings unchanged. Also use to exit or clear certain
function key operations.
CURSOR KEYS
• Press
one character at a time.
3
V
1
USER
E
A
2
A
3
R
CAPS
4
T
Line indicator
Italic Box Justify
Vertical text
Underline Barcode
and all other settings off.
CAPS
before pressing an
while
is set will give lower case
CAPS
CLEAR
+
DEL
,
,
or
or
to move the cursor along the text,
GB
1234
Fixed label
length set
first to