AFFA AFPD-022 Kullanım Talimatları Kılavuzu - Sayfa 7

Amplifikatör AFFA AFPD-022 için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. AFFA AFPD-022 8 sayfaları. Professional audio equipment power distributor

Sayfayı Yazdır

Program Operation

1.Entering into interface

When you connected the power and open the air-break switch, you will enter into a blinking LED

interface (digital tube will check all lightly or full-body). If your password is "000" (default

password), then flashes three times later, it will enter into the operation interface. Or you have to

press Up Button and Down Button to enter into the Operation Interface through the password one

by one.

2.Operation Interface

A.Stand-alone

No operation button, but showing "OFF", it means output has been closed

No operation button, but showing "ON", it means output has been opened.

When reading "OFF" on Switch, it means the output will be closed timely

When reading "ON" on Switch, it means the output will be opened timely

("1**") what is it closed or opened is the No2 channel(*2*), delay3x0.5s (*3*).

Parameter setting interface and changing the password, please refer to the relevant programming

interface operation

B.Line interface

No operation button, but showing "OPN", it means output has been closed

No operation button, but showing "CLS", it means output has been opened.

Sequential machine and Stand-alone interfaceNo parameters setting or password changing

when being carried out

3.Operation switch

In the condition that the one-way switch has not closed , enter into the user interface, you only

need to continue pressing the switch button for one second, you can switch to sequential machine

(less than 1S, operation invalid)

A.Powered on punctually

When entering into the operation interface and all the ways have been closed. Please press the

mother switch for 1 second , then it will be powered on on time . (showing ON)

When the system is closed now, please press the switch for 1 second, it will be opened on time.

B.Powered off punctually

C.When all the ways are opened , please keep pressing the mother switch for 1 second , and then

you could power off the system punctually . (showing OFF)

D.When the system is opened now, please press the switch for 1 second, it will be closed on time.

4.Specification setting

Using the UP Button and DOWN Button can check and edit the parameter. When there is any

parameter that need to be changed , please press the edit buttons, and then you will see the

delaying time in the relative channel . after editing the parameter , press the edit buttons . and

then it will come back to the first interface, which showing OFF or ON

1.Input socket

Use the 5-pin three-phase industrial power input socket. In accordance with industry standards

(the instructions on the cover is standard) , please insert three-phase lines L1, L2, L3, a zero line

N and a ground line G. Input connectors , L1/N/G, is responsible for the output of the 1-4 in the

rear board ; L2/N/G is responsible for 5-6 ;L3/N/G is responsible for 7-8.

The default connection is the three-phase line L1, L2, L3 plus a zero-line N and a ground wire G of

all connected, so that all output sockets can be used. Please Note that the phase line L1, zero-line

N and ground G have been set to work to take power by factory.

It will be very dangerous , if wiring wrong. please make sure them mark-seated. After plugging the

power firmly, please make sure the power connector correctly to remove any incipient fault for this

and the follow-up equipment.

L1-N: AC220V, 50HZ/60HZ 32A

L2-N :AC220V, 50HZ/60HZ 32A

L3-N :AC220V, 50HZ/60HZ 32A

2.Main Power Switch

Three-phase air switch with overcurrent protection and short circuit protection

Normally speaking , any phase current can not exceed 32A for AFPD-022 .Otherwise, it will be

protected automatically .

3.Voltage Display

Through the triple-digit on the LED , it will display the AC voltage of what this device connecting .

4.Programming Interface

Using a LED screen, and three LED lamps to make it display more intuitively .

5.USB Lampholders

AFPD-022 comes with a USB lampholder. Power on and insert the USB lamp , it will light . and

then facilitate the operation under weak light .

6.Output Indicator

Using Φ5 bright green lamp, each lamp corresponds to each way of output .

7.One-way switch

You can turn off a particular output. However, before booting, make sure that all one-way switches

have been switched on, so as to reduce the trouble when re-opening, but also to do an emergency

switch