AirCom SealAir2K Manuel - Sayfa 3

Hava Kompresörü AirCom SealAir2K için çevrimiçi göz atın veya pdf Manuel indirin. AirCom SealAir2K 6 sayfaları.

SCENARIO 1: SEAL PUNCTURED TIRE

This scenario details the steps involved in temporarily repairing a punctured tire using the SealAir2K Products, ensuring

proper and safe usage for an e ective temporary ﬁx.

Part 1: Pumping Tire Sealant into the Tire with

SealAir2K Bottle Attached

Peel o

the warning sticker with the maximum

permissible speed (80 km/h | 50 mph) info from the

compressor and attach it to the steering wheel.

A x the TMK decal from the SealAir2K bottle to the

wheel for quick reference.

E N G I N E

START

Turn on the car's ignition.

NOTE: Remember to engage the handbrake and shift the

gear into neutral or park.

15 min.

> 10 km (6 mi.)

If desired pressure in the tire is reached quickly start

driving 10km (6 mi.) or 15 minutes with a maximum speed

of 80 km/h (50mph).

NOTE: The tire isn't sealed yet and tire pressure is still

dropping, sealing process happens while driving.

Parts kit

Extract the hose and power plug with cable from the

SealAir2K compressor.

Securely attach the SealAir2K bottle to the compressor by

gently screwing it (90 degrees clockwise) onto the output

valve (matching lock indicators).

NOTE: Lock indicators (arrows, that you will ﬁnd on the

bottle [ O ] and compressor [ L ] ) position should be

matched.

Activate the power button on the compressor. This

initiates the sealant pumping into the tire.

NOTE: Initially, the pressure gauge may display a higher

value; do not turn o the compressor as the pressure will

decrease naturally.

Part 2: Check Tire Pressure and Inﬂate Tire

without the SealAir2K Bottle.

Stop the car and connect the compressor (instruction on

the compressor B.2) to the tire valve without the bottle.

Inﬂate the tire to the pressure speciﬁed in the car's

manual.

A - Power cable

B - Tire valve nut

C - Air hose

D - Bayonet

E - Car lighter plug

F - Nameplate

G - Air release valve

H- Bayonet connector

I - Manometer

J - Instruction Label

K - ON/OFF switch

L - Lock indicator

M - Bayonet

N - Instruction label

O - Lock indicator

P - Bayonet connector

R - Adapter

S - Air Hose

T - Air Hose thread

90°

Rotate the hose valve 90 degrees clockwise and attach it

to the SealAir2K bottle's output valve. Then, connect the

hose cable to the tire valve.

WARNING: Ensure that the bottle and hose are properly

connected to prevent pressure loss.

>1.8 bar/26 psi/180 kpa

<1.8 bar/26 psi/180 kpa

max 15 min.

Inﬂate the tire until the recommended pressure, typically

exceeding 1.8 bar/26psi/180kPa, is achieved. This process

should take no longer than 15 minutes.

WARNING: If the tire pressure does not reach 1.8 bar (26

psi/180 kPa) within 10 minutes, the tire may have

sustained excessive damage that makes a temporary

repair impossible. In this case, do not continue to use the

tire. Call for a towing service.

>2.5 bar/36 psi/250 kpa

<2.5 bar/36 psi/250 kpa

max 15 min.

Brieﬂy switch o the compressor to check the actual tire

pressure using the pressure gauge.

If the speciﬁed pressure isn't reached within 15 minutes,

consider contacting a towing service for assistance.

WARNING: If the tire's air pressure does not reach 1.8 bar (26

psi / 180 kPa) within 15 minutes, it's likely that the tire has

su ered extensive damage, making temporary repair impossi-

ble. In this scenario, do not continue using the tire; instead,

contact a towing service.

ATTENTION: If the tire is completely deﬂated, there is a

possibility of the tire separating from the rim, causing air leakage

when attempting to inﬂate it. If this occurs, jack up the vehicle to

aid inﬂation. If unsuccessful, contact a towing service.

ATTENTION: DO NOT CARRY THE COMPRESSOR IN YOUR

HANDS WHILE OPERATING, INSTEAD PLACE IT ON A HARD,

CLEAN SURFACE.

WARNING! SealAir2K Products are intended solely for

emergency tire repairs, allowing vehicles to be driven to a service

center for proper tire repair. They are not intended for use in

cases of severe tire damage. Radial ply passenger car tires may

only be repaired in the tread area. No repairs are allowed on the

bead, sidewall, or shoulder area of the tire. Exercise extreme

caution while using tools to prevent injury. Improperly connec-

ted products can cause the sealant to spray.

12 V

Plug in the 12V power cable into the car's power outlet.

Conﬁrm a secure connection.

NOTE: Ensure that the power cable is plugged in correctly

and securely.

MAX

60 SEC.

Pack TMK back to your car and start driving.

WARNING: This step shouldn't take any longer than

1 minute.

max 1000 km (620 mi.)

If desired pressure in tire is reached, you can proceed to

drive cautiously within the limitations of a maximum

distance of 1000 km (620 miles) and at a maximum speed

of 80 km/h (50 mph). (Distance can vary by tire model,

weather condition, size of puncture).

Inform all other users of the vehicle that the tire has been

temporarily sealed with the SealAir2K Products and make

them aware of the special driving limitations to be

observed.

GO!