Gaggenau Vario 400 Series Kurulum

Setüstü Ocak Gaggenau Vario 400 Series için çevrimiçi göz atın veya pdf Kurulum indirin. Gaggenau Vario 400 Series 2 sayfaları. Downdraft ventilation
Ayrıca Gaggenau Vario 400 Series için: Hızlı Başlangıç Kılavuzu (2 sayfalar), Kesik Ölçüler (4 sayfalar), Manuel (7 sayfalar)

Sayfayı Yazdır
Gaggenau Vario 400 Series Kurulum
VR 414 610
Stainless steel
Width 15" (38 cm)
Included accessories
2 cast-iron grills
1 lava stone
1 cleaning brush
1 grease collecting insert
1 cast-iron griddle, half size
Installation accessories
In combination of several Vario
cooktops or VL 414 downdraft,
connecting strips must be used.
Choose respective VA 420 strip from
one of the below, depending on type
of installation.
VA 420 010
Connection strip for
surface-mount
installation
without
appliance cover.
VA 420 011
Connection strip for
surface-mount
installation
with
appliance cover.
VA 420 000
Connection strip for
flush
installation
without
appliance cover.
VA 420 001
Connection strip for
flush
installation
with
appliance cover.
VA 440 010
Stainless steel cover with mounting
strip.
VA 450 400
Stainless steel adjustment strip, width
15". Necessary accessory in a combi-
nation of 15" Varios with at least one
appliance cover to compensate for the
appliance depth.
Optional accessories
LV 030 000
Lava stones for refilling.
VA 461 000
Cast-iron griddle, enameled, half size
For Vario electric grill 400 series. For
simultaneous searing and grilling on
two separate surfaces.
VA 461 001
Cast-iron griddle, enameled, full size
For Vario electric grill 400 series.
For searing large quantities on one
surface.
Vario 400 series electric grill
VR 414
– 2 zones, independently controlled
– Half size cast-iron griddle included
for simultaneous searing and
grilling on two separate surfaces
– Open cast-iron grill, lava stones
– Solid stainless steel control knobs
– Precision-crafted ⅛-inch stainless
steel frame
– For surface-mount installation with
a visible edge or for flush
installation
– Can be perfectly combined with
other Vario 400 series products
Operation
Control knobs with illuminated
ring, cooking zone and output level
markings.
Electronic control in 12 output levels.
Features
Cooktop, lavastone container and
grease drip tray are made from
stainless steel.
2 independently controlled heating
elements (1,500 W), front and rear.
Two-part cast-iron grill.
Safety
Safety shut-off.
Planning notes
Depending on the type of installation —
surface-/ or flush-mounted, with or
without cover — the specific location of
the control knob positions may vary.
When using the appliance cover
VA 440 or adjustment strip VA 450
additional space for cut-out depth
needs to be considered.
In a combination of Vario cooktops
with at least one appliance cover, the
adjustment strip VA 450 is required.
In a combination of several Vario 400
series cooktops a connection strip
must be used. Depending on the type
of installation — surface-/ or flush-
mounted, with or without cover — the
respective VA 420 connecting strip
must be used.
For flush installation the edge height
in the cut-out needs to be at least ½"
and for surface-mount ⅜". Ensure a
continuous cut surface of 90°.
The weight capacity and stability,
especially in case of thin counter tops,
must be supported using suitable
substructures. Take the appliance
weight and additional loads into
account.
Flush installation is possible in
countertops made of stone, synthetics
or solid wood. Heat resistance and
watertight sealing of the edges must
be observed. For other materials,
please consult with your countertop
manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the countertop cut-out.
If installing several Vario products in
individual cut-outs allow for a minimum
distance of 2" between the cooktops.
Built-in control panel can be inte grated
in the bottom cabinet at drawer level.
Front panel thickness ⅝" – 1".
The adjacent drawing "Installation of
the control knobs" must be observed
if the panel is more than 1" thick (there
must be a recess at the rear for proper
control module installation).
Above the countertop minimum
clearance of 21" from adjacent
heat-sensitive cabinets or contact 1"
surfaces must be observed or thermal
insulation must be installed.
Appliance can be snapped into the
countertop from above.
Please read additional planning notes
on pages 82 – 87.
Rating
Total rating: 3.0 kW.
Total Amps: 15 A.
208/220–240V / 60 Hz
Plan for a 70" connecting cable
without plug (hardwire required).