Great Lakes WEN 721830 Kullanım Kılavuzu - Sayfa 2
Dış Mekan Arabası Great Lakes WEN 721830 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Great Lakes WEN 721830 2 sayfaları. 18" x 30" mover dollies
Sayfayı YazdırINSTRUCTION MANUAL
GENERAL SAFETY WARNINGS
WORK AREA SAFETY
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common
sense when operating a tool. Do not use a tool while
you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating
tools may result in serious personal injury.
2. Use personal protective equipment. Always wear eye
protection. Protective equipment such as a respiratory
mask, non-skid safety shoes and hearing protection
used for appropriate conditions will reduce the risk of
personal injury.
3. Dress properly. Do not wear loose clothing or jewelry.
Keep your hair and clothing away from moving parts.
Loose clothes, jewelry or long hair can be caught in
moving parts.
TOOL USE AND CARE
1. Do not force the tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it was designed.
2. Do not use the tool if the switch does not turn it on
and off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
3. Disconnect the plug from the power source and/
or the battery pack from the tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk
of starting the tool accidentally.
4. Store idle tools out of the reach of children and do
not allow persons unfamiliar with the tool or these
instructions to operate the tool. Tools are dangerous in
the hands of untrained users.
MOVER DOLLY SAFETY WARNINGS
1. Do not climb, sit or stand on the dolly.
2. Do not exceed the loading capacity.
3. Do not use the dolly if any part is missing or damaged. Replace damaged parts immediately.
5. Maintain tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition
that may affect the tool's operation. If damaged, have
the tool repaired before use. Many accidents are caused
by poorly maintained tools.
6. Use the tool, accessories, and tool bits, etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the tool for operations different from those
intended could result in a hazardous situation.
SERVICE
1. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
CALIFORNIA PROP 65 WARNING
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities may
contain chemicals, including lead, known to the State
of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after handling. Some
examples of these chemicals are:
•
Lead from lead-based paints.
•
Crystalline silica from bricks, cement, and other
masonry products.
•
Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies depending on
how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated
area with approved safety equipment such as dust
masks specially designed to filter out microscopic
particles.
INSTRUCTION MANUAL
PACKING LIST
Components
Casters (8)
Short Wood Sides (4)
(Part 721830-001)
ASSEMBLY INSTRUCTIONS
1. Place two short wood sides (Fig. 1 - 1) on a sturdy, flat surface with the bolts (Fig. 1 - 2) facing up.
2. Fit the holes in the long wood sides (Fig. 1 - 3) over the bolts on the short wood sides as shown below.
3. Fit four casters (Fig. 1 - 4) over the bolts as shown in the figure below.
4. Secure the wood sides and casters with sixteen hex nuts (Fig. 1 - 5). Make sure that all nuts are tightly secure
before beginning operation.
5
5
5
5
4
3
2
2
2
2
1
Hex Nuts (32)
Long Wood Sides (4)
(Part 721830-002)
Fig. 1