Dynabrade 50345 Talimatlar - Sayfa 3

Sander Dynabrade 50345 için çevrimiçi göz atın veya pdf Talimatlar indirin. Dynabrade 50345 4 sayfaları. 1.2 hp right angle disc sander

Sayfayı Yazdır

Important Operating, Maintenance and Safety Instructions

Carefully read all instructions before operating or servicing any Dynabrade® Abrasive Power Tool.

Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.

Important: All Dynabrade air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.

Operating Instructions:

Warning:

Eye, face and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow

safety procedures posted in workplace.

1. With power source disconnected from tool, securely fasten abrasive/sanding pad on tool.

2. Connect power source to tool. Be careful not to depress throttle lever in the process.

3. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should

be serviced to correct the cause before use.

Maintenance Instructions:

Products offered by Dynabrade should not be converted or otherwise altered from original design without the

expressed written consent from Dynabrade, Inc.

1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to

correct the cause before use.

2. Some silencers on air tools may clog with use. Clean and replace as required.

3. All Dynabrade air motors should be lubricated with two drops of Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) placed directly into the air inlet with

throttle lever depressed every four hours of use.

4. An air line filter-regulator-lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11299 Air Line

Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and positive-drip lubrication of

pneumatic components. Operates 100 CFM @ 90 PSI has 1/2" NPT female ports.

5. Gear case of this Dynabrade air tool should be lubricated every 16 hours of use by using 95541 Grease Gun and 95542 Grease.

Safety Instructions:

•

Warning:

Eye, face and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow

safety procedures posted in workplace.

• Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).

• Operate machine for 30 seconds before application to workpiece to determine if machine is working properly and safely before work begins.

• Always disconnect power supply before changing abrasive or making machine adjustments.

• Inspect abrasives and sanding pads for damage or defects prior to and during operation of tool.

• Please refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.

• Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.

Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from

the date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall

repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our

examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,

instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect

its normal performance. Normally wearable parts such as bearings, sanding pads, rotor blades, etc., are not covered under this warranty.

Important: Manufactures warranty is void if tool is disassembled before warranty expires.

Tool Disassembly:

1. Disconnect tool from power source.

2. Insert 01697 Inlet Bushing securely into vise.

3. Roll 07136 Grip Back away from 52090 Adapter to expose wrench flats.

4. Remove 52090 Adapter from housing (right hand thread).

5. Grip onto governor cage assembly and pull motor assembly from housing.

6. Remove 02631 Nut (use a 32mm wrench – P/N 96079).

7. Separate valve from adapter.

Motor Disassembly:

1. Secure bevel pinion into a soft jaw vise.

2. Remove governor cage assembly from 07106 Rotor (left hand thread).

3. Remove rear bearing plate by securing cylinder and pressing the 07106 Rotor through the 01007 Rear Bearing.

4. Remove blades from rotor.

5. Secure bevel pinion into a soft jaw vise and press rotor shaft through the bevel pinion.

6. Remove 07119 Front Bearing Plate and 01036 Front Bearing from 07106 Rotor.

Full One Year Warranty

Disassembly/Assembly Instructions

(continued on next page)