Hi-Power Cycles HPC REVOLUTION 2017 Kullanıcı El Kitabı - Sayfa 12
Scooter Hi-Power Cycles HPC REVOLUTION 2017 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Hi-Power Cycles HPC REVOLUTION 2017 20 sayfaları.
Sayfayı Yazdır
and the life of the batteries.
2. DO NOT store lithium batteries at a fully charged state (40%-60% is ideal)
3. ALWAYS check motor nuts and bolts BEFORE AND AFTER riding to make sure nothing is loose.
Riding at high speeds induces vibrations which may loosen components on the bike. This includes
wheels, the battery rack, brake system, etc. If the nuts are not tight on the electric wheel, the axle can
spin in the dropouts leaving broken wires and damaged forks. These nuts must be very tight to assure
the proper performance.
*HI POWER CYLCES IN NOT RESPONSIBLE FOR SPUN OUT DROP OUTS OR BROKEN WIRES!*
4. ALWAYS check that the motor is securely fastened to the frame
5. ALWAYS check the integrity of the rack and battery system (or frame mounted battery). Make sure it is
securely fastened to the bike
6. Check spokes on both wheels. The electric wheel often requires more attention due to the torque of the
motor. Spoke and wheel maintenance are part of a normal bicycle maintenance procedure and will be
accelerated with an electric motor. Do not take chances with the spokes and if you think they are
loose, chances are you are correct. The spokes should all have the same tension. If they are loose, tighten
them yourself, or take it to your local bike shop to get fixed.
7. Check the pressure in your tires. The required pressure can be found on the sidewall of the tire. Normal
pressure is 45-55 PSI. Tires lose an average of 2-3 PSI per week. Low pressure will cause sidewalls to
collapse, and that is how most blowouts occur. HPC IS NOT RESPONSIBLE FOR FLAT TIRES!
8. Check all electrical connections making sure that they are all tight. Bad contact means energy is wasted as
heat, which can cause a breakdown of wire insulation. Any wire with melted insulation indicates a poor
connection nearby. Disconnect the batteries and do not operate if insulation is melted or wire is exposed.
Important Information About 4000+ Watt Systems
All systems > 4000w are equipped with drilled side covers to prevent overheating and allow your bike to
perform at full performance for much longer. The vented side covers also allow the bike to be ridden in
wetter conditions since they give the motor the ability to shed the water through the holes and dry
completely. It comes from the factory with a special corrosion resistant coating on the inside of the motor to
help prevent rust build up. It is important to note that this does require minimal maintenance. Since water can
corrode metal over time, it is recommended to spray
Boeshield T-9
after every 10-15 rides or so to prevent
corrosion from occurring. The motor will come pre-treated from our factory. Also, if you live in a dusty
environment, it is also important to prevent debris and dust from entering in the holes. Prior to spraying the
motor with Boeshield, attempt to clean the motor with an air compressor or a can of compressed air. Doing
these things will greatly prolong the life of your motor and keep it running at its peak level!
3.8 Safety:
1. ALWAYS wear proper safety equipment
2. NEVER operate at speeds that exceed your ability to operate the bike safely
3. ALWAYS know your surrounding and actively scan the terrain for obstacles
4. DO NOT wear loose fitting clothes or articles
5. NEVER ride with more than 1 rider
6. Suitable for riders 16 and older. NO EXCEPTIONS!
7. Know your bike and personal limits
IF ANY INJURIES OR HARM OCCUR WHEN YOU USE THE PRODUCT, THE
MANUFACTURER OR DISTRIBUTOR WILL NOT BEAR ANY RESPONSIBILITY
3.9 Getting the Stated Range out of Your System
In the electric bike world, most manufactures quote maximum range at 20 watt hours per mile for an electric
system. This is in the BEST CASE SCENARIO in the real world, with little to no pedaling. When giving
our range estimates, we are talking about a 170lb rider, totally flat ground, smooth surface, no wind and
cruising in the most efficient range of the system. For instance, on our 2000w system with 12.5ah battery,
using this calculation we would get 32.3 miles maximum range (51.8v x 12.5ah = 647.5. 647.5 watt-hours