Dynabrade 52633 İşletme ve Bakım

Öğütücü Dynabrade 52633 için çevrimiçi göz atın veya pdf İşletme ve Bakım indirin. Dynabrade 52633 8 sayfaları. 4", 4-1/2", 5" right angle grinders

Sayfayı Yazdır

4", 4 -1/2", 5" Right Angle Grinders

Model

Wheel Size

52630

52632

4-1/2"

52633

FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND ACCESSORIES @ WWW.DYNABRADE.COM

Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating personnel

as well as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Standards

Institute (ANSI) Safety Code for Portable Air Tools – B186.1. For additional safety information, refer to Safety Requirements for the

Use, Care and Protection of Abrasive Wheels – ANSI B7.1, Code of Federal Regulation – CFR 29 Part 1910, European Committee for

Standards (EN) Hand Held Non-Electric Power Tools – Safety Requirements and applicable State and Local Regulations.

Read and understand tool manual before

work starts to reduce risk of injury to

operator, visitors, and tool.

Eye protection must be worn at all times,

eye protection to conform to ANSI Z87.1.

Respiratory protection to be used when exposed to

contaminants that exceed the applicable threshold

limit values required by law.

Some dust created by grinding, sanding, drilling, and other construction activities contain chemicals known to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement and other masonry products

• Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Carefully Read all instructions before operating or servicing any Dynabrade

Products offered by Dynabrade are not to be modified, converted or otherwise altered from the original design without expressed written consent from Dynabrade, Inc.

Tool Intent: 4"- 5" Right Angle Grinders are ideal for material removal using Type 27 depressed center grinding wheels, or Type 27 abrasive flap disc wheels.

This power tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electrical power.

Training: Proper care, maintenance, and storage of your air tools will maximize their performance.

• Employer's Responsibility – Provide 4"- 5" Right Angle Grinder operators with safety instructions and training for safe use of tools and accessories.

Accessory Selection:

• Follow tool and wheel specifications charts before choosing size and type of accessory.

• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.

• Only use recommended fittings and air line sizes. Air supply hoses and air hose accessories must have a minimum working pressure of 150 PSIG (10 Bars, g) or 150 percent of the maximum

pressure produced in the system, whichever is higher. (See Machine Specifications table on back cover.)

Air Tool Manual – Safety, Operation and Maintenance

SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL

RPM

Spindle Thread

13,500

3/8"- 24

12,000

5/8"-11

12,000

5/8"-11

WARNING

SAFETY LEGEND

WARNING

SAFETY INSTRUCTIONS

Abrasive Power Tool.

Do Not Use Tool For Anything Other Than Its Intended Applications.

(continued on next page)

Practice safety requirements. Work alert,

have proper attire, and do not operate tools under

the influence of alcohol or drugs.

Ear protection to be worn when exposure to sound,

exceeds the limits of applicable Federal, State or

local statues, ordinances and/or regulations.

Air line hazard, pressurized supply lines and flexible

hoses can cause serious injury. Do not use damaged,

frayed or deteriorated air hoses and fittings.

WARNING

Parts Page Reorder No. PD07•38

Effective December, 2007

Model 52632

Shown

WARNING