Dynabrade 64500 Manuel - Sayfa 2
Öğütücü Dynabrade 64500 için çevrimiçi göz atın veya pdf Manuel indirin. Dynabrade 64500 7 sayfaları. Bandsaw blade grinder
Sayfayı Yazdır
10. Do not abuse cord. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges.
11. Do not overreach. Keep proper footing and balance at all times.
12. Maintain tools with care. Keep tools clean for better use and safer performance. Follow instructions for changing accessories. Inspect tool cords
periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles
dry, clean and free from oil and grease.
13. Do not leave tool running. Disconnect tools when not in use, before servicing, when changing belts, contact arms, etc.
14. Remove keys and wrenches. Form a habit of checking to see that all keys and adjusting wrenches are removed from tool before turning it on.
15. Avoid accidental starting. Be sure switch is off when plugging in.
16. Out-door use extension cords. When tool is used outdoors, use only extension cord suitable for outdoor use. They should be marked with the
suffix W-A (for UL) or W (for CSA in Canada).
17. Stay alert. Watch what you are doing. Use common sense. Do not operate tool when you are tired.
18. Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of moving parts, breakage of moving parts, binding of moving parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced. Do not use tool if switch does
not turn tool on or off.
19. Avoid gaseous areas. Do not operate electric tools in gaseous or explosive atmospheres. Motors in these tools normally spark, and the sparks
can ignite fumes.
20. Do not alter or misuse tool. This tool is precision built. Any alteration or modification not specified is misuse and may result in a dangerous condition.
Only these accessories and attachments that are found in this instruction manual are acceptable for use with this tool. The use of any other accessory or
attachment might present a risk to the operator.
21. Replacement parts. When servicing, use only identical replacement parts. When ordering replacement parts, please specify model and serial
numbers of your machine.
22. Do not operate tool without guards. Always replace guards after changing contact arm or abrasive belt.
23. Do not mix grind material. There is a potential combustion hazard if ferrous and non-ferrous grinding dust is mixed. Clean inside
machine between materials.
24. Use hearing protection. Permanent hearing loss can result from high process noise levels.
25. Use correct width abrasive belt. Using abrasive belt that is narrower than the contact wheel can cause snagging of the workpiece.
Voltage Warning
Before connecting the tool to a power source (receptacle, outlet, etc.), be sure the voltage supplied is the same as what is specified on the nameplate
of the tool. A power source with greater than that specified for tool can result in serious injury to the user as well as damage to the tool. Using a power
source with voltage less than the nameplate rating is harmful to the tool's motor. If in doubt, do not plug in the tool.
Polarized Plugs: To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way.
Warning: Keep extension away from the immediate working area.
Electric motor maintenance should be performed as recommended by the motor manufacturer.
There are three grease fittings found on this machine, grease these fittings as needed. Please see assembly views to locate grease fittings.
Good housekeeping is essential to insuring long life of any machine tool. By keeping the machine clean and visually inspected for any wear, the machine
will provide many years of service.
Before each use inspect the contact wheels, idler rolls and drive pulley for any signs of wear. Repairing or replacing worn parts early enough will prevent
other parts from becoming damaged.
All Dynabrade tools use the highest quality parts and metals available and are machined to exacting tolerances. Our warranty obligation is contingent upon
proper use of our tools and cannot apply to equipment which has been subjected to misuse or a lack of maintenance during the use of this tool.
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the
date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall
repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our
examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,
instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to
affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
(continued on next page)
Maintenance Instructions
Notice
One Year Warranty
2