GREAT PLANES Cosmic Wind Kullanım Kılavuzu - Sayfa 3

Oyuncak GREAT PLANES Cosmic Wind için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. GREAT PLANES Cosmic Wind 20 sayfaları.

Sayfayı Yazdır

GREAT PLANES Cosmic Wind Kullanım Kılavuzu

2. You must assemble the model according to the

instructions. Do not alter or modify the model, as doing so

may result in an unsafe or unﬂ yable model. In a few cases

the instructions may differ slightly from the photos. In those

instances the written instructions should be considered

as correct.

3. You must take time to build straight, true and strong.

4. You must use an R/C radio system that is in ﬁ rst-class

condition, and a correctly sized motor and components

throughout the building process.

5. You must correctly install all R/C and other components

so that the model operates correctly on the ground and

in the air.

6. You must check the operation of the model before every

ﬂ ight to insure that all equipment is operating and that the

model has remained structurally sound. Be sure to check

clevises or other connectors often and replace them if they

show any signs of wear or fatigue.

7. If you are not an experienced pilot or have not ﬂ own this

type of model before, we recommend that you get the

assistance of an experienced pilot in your R/C club for

your ﬁ rst ﬂ ights. If you're not a member of a club, your

local hobby shop has information about clubs in your area

whose membership includes experienced pilots.

8. WARNING: The fuselage and wheel pants included in this

kit are made of ﬁ berglass, the ﬁ bers of which may cause

eye, skin and respiratory tract irritation. Never blow into a

part (wheel pant) to remove ﬁ berglass dust, as the dust

will blow back into your eyes. Always wear safety goggles,

a particle mask and rubber gloves when grinding, drilling

and sanding ﬁ berglass parts. Vacuum the parts and the

work area thoroughly after working with ﬁ berglass parts.

We, as the kit manufacturer, provide you with a top quality,

thoroughly tested kit and instructions, but ultimately the

quality and ﬂ yability of your ﬁ nished model depends

on how you build it; therefore, we cannot in any way

guarantee the performance of your completed model,

and no representations are expressed or implied as to the

performance or safety of your completed model.

Remember: Take your time and follow the instructions to

end up with a well-built model that is straight and true.

DECISIONS YOU MUST MAKE

This is a partial list of items required to ﬁ nish the "Cosmic

Wind EP" that may require planning or decision making before

starting to build.

Radio Equipment

A 4-channel radio system with four micro servos and receiver

are required for this plane. The servos and receiver shown

in the manual are Futaba® S3114 Micro High Torque Servo

and the Futaba R617FS receiver.

Transmitter

4-channel

Receiver

7-channel [FUTL7627]

❍ (3) Futaba S3114 Micro High Torque Servos [FUTM0414]

[21 oz-in (1.5kg-cm) of torque]

Connectors

❍ (1) 9" extensions [FUTM3910]

Motor Recommendations

The Cosmic Wind ARF comes with a mounting plate for the

ElectriFly

RimFire brushless outrunner motor. The motor has

been tested with this plane and works well.

❍ ElectriFly RimFire .10 Brushless Outrunner Motor

[GPMG4595]

If using the recommended RimFire Brushless Outrunner

Motor, we recommend the APC 8×8E electric propeller

[APCQ4116] for good speed performance. For better vertical

performance, with a slight reduction in speed, use the APC

9×7.5E [APCQ4119].

Electronic Speed Control

A brushless ESC (electronic speed control) is required for

the recommended motor set-up. We recommend using the

ElectriFly Silver Series SS-35A Brushless ESC [GPMM1830].

Flight Battery

The Cosmic Wind EP ARF has been ﬂ own with the ElectriFly

Power Series 11.1V 1500mAh LiPo battery and the Flight

™

Power EON-X

Lite 11.1V 1600mAh LiPo battery packs. In

our testing we found that if the APC 8×8E propeller was used

with the recommended motor, the static current draw was

approximately 24 amps.

❍ ElectriFly Power Series LiPo 1800mAh 11.1V 25C

discharge w/balance plug [GPMP0515]

❍ FlightPower

EON-X Lite LiPo 1600mAh 11.1V 25C

discharge w/balance plug [FPWP4146]

Recommended Charger

A LiPo compatible charger is required to charge LiPo batteries.

The Great Planes ElectriFly PolyCharge4

LiPo packs only; however, it is able to charge four LiPo packs

simultaneously. The ElectriFly Triton 2

chargers will only charge one pack at a time, but are capable

of charging NiCd, NiMH, Pb acid and LiPo batteries.

❍ Great Planes ElectriFly PolyCharger4 DC only 4

Output LiPo Charger (GPMM3015)

❍ Great Planes ElectriFly Triton2 DC Computer Peak

Charger (GPMM3153)

Servos

Propeller

™

is designed for

™

and AC/DC Triton2 EQ