GREAT PLANES Firebat Kullanım Kılavuzu - Sayfa 3
Oyuncak GREAT PLANES Firebat için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. GREAT PLANES Firebat 20 sayfaları.
Sayfayı Yazdır
ADDITIONAL ITEMS REQUIRED
Flight Equipment
The Firebat ARF requires a three-channel radio with two
servos, a receiver and an electronic speed controller with
BEC. A full-size receiver and standard servos can be used.
You will also need a 10" [254mm] (or 12" [305mm]) servo
extension wire.
Flight performance and maneuverability can be improved
with dual aileron servos. You will need a mini servo for the
canard (elevator) with at least 30 oz. in. of torque and two
micro/mini servos for the ailerons with at least 15 oz. in. of
torque. You will also need a mini or micro receiver, a speed
controller and a 18" [457mm] (or 24" [610mm]) servo extension
wire. This will require a four-channel radio system with
mixing functions.
Servos:
(HCAM0110) CS-12, 35 oz in torque
(FUTM0033) S3101, 34.7 oz in torque
(HRCM3401) HS-81J, 36 oz in torque
For dual aileron servos:
(HCAM0100) CS-15, 15 oz in torque
(FUTM0041) S3106, 16.7 oz in torque
(HRCM0981) HS-55J, 15 oz in torque
Mini Receivers:
(GPML0040) 4-channel FM, high band
(GPML0041) 4-channel FM, low band
(FUTL0407) 4-channel AM, low band
(FUTL0408) 4-channel AM, high band
(HRCL1535) 4-channel FM
low band - channels 11-35
high band - channels 36-60
Receiver crystal:
(FUTL62**) for GPM low band
(FUTL63**) for GPM high band
(FUTL47**) for FUT low band
(FUTL48**) for FUT high band
(HRCL23**) for HRC
** desired channel
Speed Control:
(GPMM2010) C-10, 12 amp
(GPMM2020) C-20, 20 amp
Servo Extension Wire:
(1) 10" (or 12") extension wire with standard receiver
(1) 18" (or 24") extension wire with micro receiver
Additionally, an 8-cell (9.6 volt) 600 to 1200 mAh battery
pack is required.
(GPMP0200) – 700 mAh NiCd
(GPMP0310) – 1100 mAh NiCd
Building Supplies
In addition to common household tools, here is the list of
items used to build the Firebat ARF.
❏
6-minute epoxy (GPMR6042)
❏
1/2 oz. Thin CA+ (GPMR6001)
❏
Hobby knife (HCAR0105)
❏
#11 blades (HCAR0211)
❏
Drill and 1/16" drill bit
❏
Cellophane tape (for hinging ailerons)
❏
Double-sided foam tape (GPMQ4440) for mounting
receiver and speed control
❏
Sandpaper and sanding block
❏
Small phillips screwdriver (#1)
❏
Flat blade screwdriver
❏
Small T-pins (HCAR5100) or craft pins
REPLACEMENT PARTS
If needed, replacement parts for your Firebat Electric ARF
are available through your hobby supplier. See the photo
and "Parts List" on page 4 for a reference of the parts
listed below.
(GPMG0330) Motor
(GPMQ1700) Propellers
(GPMA2372) Canard Set
(GPMA2373) Canopy
(GPMA2374) Rear Hatch
(GPMA2375) Vertical Fin Set
(GPMA2376) Fuselage Set
(GPMA2377) Hardware Pack
3