GREAT PLANES Seawind EP Kullanım Kılavuzu - Sayfa 3

Oyuncak GREAT PLANES Seawind EP için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. GREAT PLANES Seawind EP 20 sayfaları.

Sayfayı Yazdır

GREAT PLANES Seawind EP Kullanım Kılavuzu

5. You must correctly install all R/C and other components

so that the model operates correctly on the ground and in

the air.

6. You must check the operation of the model before every

ﬂ ight to insure that all equipment is operating and that the

model has remained structurally sound. Be sure to check

pushrod connectors often and replace them if they show any

signs of wear or fatigue.

7. If you are not an experienced pilot or have not ﬂ own

this type of model before, we recommend that you get the

assistance of an experienced pilot in your R/C club for

your ﬁ rst ﬂ ights. If you're not a member of a club, your local

hobby shop has information about clubs in your area whose

membership includes experienced pilots.

8. While this kit has been ﬂ ight tested to exceed normal use,

if the plane will be used for extremely high-stress ﬂ ying, such

as racing, or if a motor larger than the one recommended

will be used, the modeler is responsible for taking steps to

reinforce the high-stress points and/or substituting hardware

more suitable for the increased stress.

We, as the kit manufacturer, provide you with a top quality,

thoroughly tested kit and instructions, but ultimately the

quality and ﬂ yability of your ﬁ nished model depends

on how you build it; therefore, we cannot in any way

guarantee the performance of your completed model,

and no representations are expressed or implied as to the

performance or safety of your completed model.

Remember: Take your time and follow the instructions to

end up with a well-built model that is straight and true.

ADDITIONAL ITEMS REQUIRED

Following is the list of hardware and accessories required to

ﬁ nish the Seawind. Order numbers are provided in parentheses.

Adhesives

The list of accessories required to complete the Seawind is

rather straightforward–with the exception of adhesives which

deserve a quick discussion. Hardly any glue is used to build

the Seawind, but it must be the right kind. With the exception

of slow-drying glue such as epoxy or waterproof white glue

(which should be used for the horizontal stabilizer so there

will be time for alignment), the rest of the model could be

assembled with foam-safe CA. But it wouldn't be economical

to purchase two different kinds of glue when so little of either

is used. So if you don't have any glue at all, or if you already

have some waterproof white glue or epoxy, you could do all

the gluing with just that. But if you don't want to wait for the

glue to dry on the rest of the parts you could also purchase

some foam-safe CA. Following are some suggestions for the

kinds of glue:

❏

J&Z Products R/C-56 waterproof white glue (JOZR5007)

❏

1 oz Great Planes Pro

Glue (GPMR6069)

❏

4 oz. Great Planes Pro 6-minute epoxy (GPMR6042)

❏

CA accelerator (GPMR6035)

Hardware & Accessories

❏

4-channel mini receiver (Futaba

low band or FUTL0443 high band)

❏

Matching Rx crystal (FUTL62** low band or FUTL63**

high band)

❏

(3) Micro servos (Futaba S3114 – FUTM0414)

❏

6" [150mm] Servo extension wire (for connecting aileron

servo to receiver – FUTM4506)

❏

Great Planes RimFire

brushless motor (GPMG4560)

❏

Great Planes Silver Series 25 Amp Brushless

ESC (GPMM1820)

Motor Battery (see "Average Maximum Flight Time"

chart on page 15):

❏

Great Planes LiPo 11.1V 910mAh 20C Discharge

w/Balance (GPMP0605)

-or-

❏

Great Planes LiPo 11.1V 1250mAh 20C Discharge

w/Balance (GPMP0609)

-or-

❏

Great Planes LiPo 11.1V 1500mAh 20C Discharge

w/Balance (GPMP0613)

❏

LiPo battery charger (Great Planes PolyCharge4

DC-Only – GPMM3015)

❏

One charge lead for each battery to be charged

simultaneously (GPMM3148)

❏

12 Volt source for powering charger (Hobbico

Power Supply – HCAP0250)

Building Supplies

❏

™

Great Planes Pro

Threadlocker (GPMR6060)

❏

Common hobby tools (wire cutters, small Phillips

screwdrivers, hobby knife)

❏

Great Planes Segmented Lead Weights (GPMQ4485)

❏

RTV silicone cement or white glue

❏

Drill bits: 1/16" [1.6mm], #60 (.040") [1mm] to #52

(1/16") [1.6mm], #60 (.040") [1mm] to #58

(.042") [1.07mm]

❏

1.5mm Hex wrench

Note: The small drills are for drilling holes for the servo

mounting screws. If small drill bits are not available or if you

prefer not to purchase them, the small screw holes could

be made with a #11 hobby blade, but care must be taken

because it can be easy to oversize holes made this way.

™

Foam Safe CA+ Medium

R114F – FUTL0442

™

28-30-950kV Out-Runner

™

12 Volt