7th Sense R 10 Series Donanım Kullanıcı Kılavuzu

Sunucu 7th Sense R 10 Series için çevrimiçi göz atın veya pdf Donanım Kullanıcı Kılavuzu indirin. 7th Sense R 10 Series 2 sayfaları.

Sayfayı Yazdır

Specification

Environmental Characteristics

Temperature

Humidity (non-condensing)

Altitude

Specification

Rating/Description

Rackmount Dims (H × W × D)

3U × 483 mm × 620 mm

Rackmount weight (approx.)

22 kg

Dual Redundant Power Supply

100-240 V 8 A, 50-60 Hz

Power

800 W

Cooling

Forced air

End of Service Life

Dispose of the equipment and any components in accordance with all local and

national safety and environmental requirements. Caution: risk of explosion or leakage

of flammable liquids or gas. Any batteries should not be subject to extremely low pressure,

extremely hot environments, disposed of in fire or mechanically crushed or cut.

Regulatory Compliance Statements

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with this user guide, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at their own expense.

European Union

This is a Class A product. In a domestic environment, this product may cause radio interference,

in which case the user may be required to take adequate measures.

7thSense Design Ltd : 2 The Courtyard, Shoreham Road, Upper Beeding, BN44 3TN, UK

www.7thsense.one

Operating

Non-operating

+15 to +30

-10 to +50 °C

10 to 90%

5 to 95%

≤ 2000 m

≤ 10000 m

Notes

Autoranging, IEC 60320 inlets

Front inlets, rear exhaust

R-Series 10 Server

Hardware User Guide

Customer Support Portal: https://portal.7thsense.one

Support

If your R-Series 10 server was purchased through one of our regional distributors, please

contact your supplier directly for support.

Visit our customer support portal where you can find a wide range of support documentation

and video tutorials, together with contact information.

Warranty

Standard warranty is 24 months, return-to-supplier. Please contact your supplier if you require

an extended warranty. Please ask for instructions and request authorisation before returning a

server to your supplier.

Operating Instructions

Operating instructions for your server can be found in the Online User Guides section of the

customer support portal.

Handling and Installation

Unpacking

Unpack your server carefully onto a clean and level surface and examine it for any signs of

transit damage. Contact your supplier immediately if anything appears to be damaged, or any

parts missing. Please retain all packaging in case of future need to return a server.

Lifting

The weight is stated below and on the server's product label. R-Series 10 require a two-person

lift, especially when manoeuvring into a rack. Observe your internal manual handling

recommendations to avoid injury.

Rack mounting

The fascia panel must be removed before mounting. Remove the two small retaining screws

bottom left and right, and then pull the fascia away. Refit the fascia after mounting.

3U units are supplied with rack mount slide rails and fixings, installation instructions are

included with the slide rails.

Ensure that each server is properly secured to the rack cabinet.

Rack stability warnings:

•

Ensure the rack is stable (e.g. bolted to the floor) before sliding out the server.

•

Do not place objects on equipment projecting from a rack (e.g. do not use as a shelf).

Only slide out one piece of equipment from the rack at a time.

•

March 2023