2gig Technologies 2GIG-FT1-345 Kurulum Talimatları

Güvenlik Sensörleri 2gig Technologies 2GIG-FT1-345 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. 2gig Technologies 2GIG-FT1-345 2 sayfaları. Flood and temperature detector
Ayrıca 2gig Technologies 2GIG-FT1-345 için: Manuel (2 sayfalar)

Sayfayı Yazdır

INSTR,INSTL,2GIG-FT1 TEMP FLOOD SENSOR - P/N: 10008993 A- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.5000" X 11.000" - TOL. +/- 0.125"- SCALE: 1-1 - PAGE 1 OF 2- FOLDING: FOLD 4X TO FINAL SIZE: 2.125" X 2.750"- FINISH WITH LOGO SHOWING

2GIG-FT1-345

FLOOD AND TEMPERATURE DETECTOR

INSTALLATION INSTRUCTIONS

The 2GIG-FT1-345 is a fully supervised, tamper protected one-way 345 MHz

sensor. It will monitor the ambient temperature and/or will detect a wet/dry ﬂ ood

condi on. The sensor reports wet/dry condi ons and temperature to the panel.

Flood Conditions

Once the sensor probe detects the presence of water for three (3) minutes, the

integral transmi er will send a wet alarm transmission to the panel. The probe will

also send a restore (dry) report when the presence of liquid is no longer detected

by the ﬂ ood probe for three (3) minutes. For ﬂ ood repor ng the sensor requires

the installa on of the supplied external ﬂ ood probe. The sensor is capable of

detec ng clean or dirty fresh water, salt water, or tap water.

Temperature Conditions

Heat:

1. If the temperature is more than 95° F (35°C) for ﬁ ve (5) minutes, the sensor

will send a loop 2 transmission.

2. If the temperature is less than 95°F (35°C) for ﬁ ve (5) minutes, the sensor will

send a loop 2 clear.

Cold:

1. If the temperature is less than 41°F (5°C) for ﬁ ve (5) minutes, the sensor will

send a loop 3 transmission.

2. In the temperature is more than 41°F (5°C) for ﬁ ve (5) minutes, the sensor

will send a loop 3 clear.

Contents

Verify that the package includes the following:

• 1—2GIG Flood/Temperature Sensor

• 1—Sensor Mounting Plate

• 1—3V Lithium Battery ( Panasonic CR15H270 uninstalled)

• 3—3/8" Phillips Screws

• 1—Double Stick Tape Strip

• 1—Probe Mounting Plate

Installation Tools Required

• Phillips Screwdriver

Figure 1.Temperature/Flood Sensor Contents

A Double S ck Tape Strip

B Sensor Moun ng Plate

C Probe Moun ng Plate

D 3V Lithium Ba ery

E Phillips Screws (3/8")

F Flood Probe Cord

G Flood Probe

H Transmi er with Integral Temperature Sensor

Installing and Replacing Battery

Open Sensor Case as show in Figures 2 and 3.

Install or replace ba ery.

PRINTER'S INSTRUCTIONS:

Figure 2. Opening Sensor Case

Grip the base of the sensor case. Place thumb on tab and push down un l sensor

case separates.

Figure 3. Separate Sensor Case

Figure 4. Installing New Ba ery

BATTERY

Installing a New Battery and System Programming

NOTE: Do not install ba ery un l panel is in Sensor Programming Mode.

1. Place panel in Sensor Programming mode

2. Insert ba ery

3. Close sensor

Replacement Battery Installation:

NOTE: If ba ery has been previously installed

1. Remove ba ery and dispose of (mee ng state regula ons)

2. Wait two (2) seconds

3. Replace ba ery

4. Close sensor

Installing/Mounting Flood/Temperature Sensor

The 2GIG-FT1-345 Flood and Temperature Sensor includes two methods of

installa on:

1. Double S ck Tape Installa on (See Figure 5).

2. Screw/Moun ng Plate Installa on (See Figure 6).

It is strongly recommended that the Flood/Temperature Sensor be mounted using

screws (provided) and Moun ng Plate (provided).

Figure 5. Double S ck Tape Moun ng Sensor Moun ng Plate

FLOOD/

TEMPERATURE

SENSOR

MOUNTING

PLATE

1. PUSH DOWN ON

THUMB TAB.

2. PULL BACK PLATE

OFF OF COVER

REMOVE SENSOR

COVER FROM

SENSOR BASE

TEMPERATURE/

FLOOD SENSOR

BASE

BATTERY REMOVAL

AND/OR INSTALLATION

APPLY DOUBLE STICK

WALL

TAPE TO BACK OF

MOUNTING PLATE

FIRST

PUSH

SENSOR

ONTO

MOUNTING

DOUBLE

PLATE

STICK

TABS

TAPE

THEN PUSH

STRIP