ADEMCO VISTA-15P Hızlı Kurulum Kılavuzu

Güvenlik Sistemi ADEMCO VISTA-15P için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. ADEMCO VISTA-15P 2 sayfaları. Programming auto arming and disarming schedules
Ayrıca ADEMCO VISTA-15P için: Hızlı Kurulum Kılavuzu (2 sayfalar), Programlama Kılavuzu (17 sayfalar), Kullanıcı Kılavuzu (20 sayfalar), Programlama Kılavuzu (17 sayfalar), Hızlı Kurulum Kılavuzu (2 sayfalar), Programlama Kılavuzu (2 sayfalar), Hızlı Kılavuz (2 sayfalar)

Sayfayı Yazdır

ADEMCO VISTA-20P / VISTA-20PSIA and VISTA-15P / VISTA-15PSIA

Quick Installation Guide

(FOR DOCUMENTATION AND ONLINE SUPPORT: http://www.security.honeywell.com/hsc/resources/MyWebTech

1. Mount the Control.

1. Mount the control cabinet to a sturdy wall in a clean, dry area, which is not readily accessible to the

general public, using fasteners or anchors (not supplied) with the four cabinet mounting holes.

2. Remove cabinet door, then remove the lock

knockout from the door. Insert the key into the

CHECK

POSITION

lock

LOCKED

3. Position the lock in the hole, making certain that

the latch will make contact with the latch bracket

when the door is closed. When correctly

positioned, push the lock until the snap tabs hold

it securely.

CABINET DOOR

The cabinet can be secured without a lock by

using 2 screws in the cover's edge.

Installing the Cabinet Lock

4. Before installing the cabinet's contents, remove the cabinet knockouts needed for wiring entry. Do not

remove the knockouts after the PC board has been installed.

5. Mount the PC Board. Refer to the diagram below.

CIRCUIT

BOARD

CABINET

DETAIL A

SIDE VIEW

OF BOARD SUPPORTING

SLOTS

INSERT THE TOP OF THE

(PROVIDED) ON THE RAISED CABINET TABS.

CIRCUIT BOARD INTO THE

SLOTS AT THE TOP OF THE

CABINET

Mounting the PC Board

3. Connect the Transformer & Battery.

1321 Transformer (1321CN in Canada)

• Do not plug the transformer into the AC outlet until all wiring connections to the control are complete. As

a safety precaution, always power down the control when making such connections.

1361X10 Transformer

(required if using Powerline Carrier devices)

1. Splice one end of a 3-conductor cable to the wire ends of the SA4120XM-1 cable.

2. Connect the SA4120XM-1 cable plug to the 8-pin connector on the control.

3. Connect the other end of the 3-conductor cable to the 1361X10 Transformer.

Canadian Installations: For Powerline Carrier Devices, use the PSC04 X-10 Interface and trigger

connector pins.

Battery Connections

• After all connections to the control are completed and after AC power has been applied, connect the

red and black flying leads on the control board to the battery.

• This control will not power-up on battery alone (AC power must be applied). However, once the system is

powered up, it will operate on battery if AC is lost.

UL For UL installations and Residential fire installations, refer to the chart below for the correct battery

size required to meet the mandatory standby time.

CALIFORNIA STATE FIRE MARSHALL (CSFM) AND UL RESIDENTIAL FIRE

24-HOUR BATTERY BACKUP REQUIREMENTS

The California State Fire Marshal and UL have regulations which require that all residential fire alarm

control panels must be provided with a backup battery which has sufficient capacity to operate the panel

and its attached peripheral devices for 24 hours in the intended standby condition, followed by at least 4

minutes in the intended fire alarm signaling condition. This control panel can meet these requirements

without using a supplementary power supply, provided that the panel's auxiliary power and bell output

currents are limited as listed below.

OUTPUT LIMITATIONS AND REQUIRED BATTERIES

OUTPUT CURRENT LIMITS

BATTERY INFORMATION

Current Total

Max. Aux.

Battery Capacity

Recommended Battery

Current

(Amp/Hrs)

(Yuasa Model No.)

600mA

45mA

4AH

NP4-12 (or ADEMCO 467)

maximum total

160mA

7AH

NP7-12

of auxiliary

200mA

8AH

NP4-12 (two) ‡

power plus bell

425mA

14AH

NP7-12 (two) ‡

output currents

500mA

17.2AH

NPG18-12

‡

NOTE: Use two batteries, connected in parallel. Obtain an Ademco Battery Harness Kit SA5140-1. (Both batteries will

fit inside the cabinet.)

ÊK5305-1QG0Š

K5305-1QG 1/09 Rev. A

2. Connect Devices, Zones, Sounder, and Phone Line.

Refer to the Wiring Diagram on the reverse side for connection information. NOTE: This system uses a range of reserved addresses for each type of device.

1. Connect keypads and other addressable devices to the ECP terminals 4-7.

PUSH

Refer to the wiring chart below for wire sizes and maximum wire run lengths.

ON LOCK

UNTIL IT

SNAP

Wire Chart For Devices Drawing Aux Power From The Control (12V+ & 12V–)

IS SEATED

TAB

SECURELY

Wire

TOTAL CURRENT OF ALL DEVICES CONNECTED TO A SINGLE WIRE RUN

PUSH

Size 50 mA or less

#22

900ft (274m)

#20

1400ft (427m)

SNAP

UNLOCKED

TAB

#18

1500ft (457m)

#16

1500ft (457m)

STEP 1

STEP 2

BOTTOM

The length of all wire runs for both partitions combined must not exceed 1500 feet (457m) when unshielded quad

conductor cable is used (750 feet if shielded cable is used).

Standard Keypads (6150 / 6160 series)

• Set each keypad's address (16-23) accordingly. Address 16 is reserved for the first keypad and is

always enabled in the control.

• Use data fields *190-*196 to enable keypads and set their sounding options.

CIRCUIT

CABINET

BOARD

Expander Modules (4219, 4229)

• Set each module's address (07-11) using the module's DIP switches.

• Use *56 Menu mode to program zone characteristics.

DETAIL B

Touchscreen Keypads (6270 / 6271 series, 8132 series)

SIDE VIEW

OF MOUNTING CLIPS

• Set each touchscreen's address accordingly (01, 02, 05, 06) and enable in field ∗189.

HANG TWO SHORT MOUNTING CLIPS

• Make sure the auxiliary current drain is within the control's limitation. Otherwise use an external

SECURE THE BOARD TO THE

power supply to power the touchscreen keypads.

CABINET WITH THE ACCOMPANYING

SCREWS

cb_mount-001-V1

Relay Modules (4204)

• Connect desired field wiring to the module's relay contact terminals.

• Set each module's address (12-15) using the module's DIP switches.

• Use ∗79 / ∗80 Menu modes to enter each device address and define functions.

RF Receiver (5881, 5883, RF Keypad)

• Set the receiver's address to 00 using the module's DIP switches.

• If using wireless keypads, set field ∗24 RF House ID Code appropriately.

If receiver is mounted remotely, note the following:

• Do not locate the receiver or transmitters on or near metal objects. This will decrease range and/or

block transmissions.

• Do not locate the RF receiver in an area of high RF interference (indicated by frequent or

prolonged lighting of the receiver's LED; random flicker is OK).

• Do not locate RF receiver closer than 10 feet from any keypads.

4. Program the Control.

Refer to the Programming Guide to program the control.

(

The control can also be programmed via the Compass Downloader.)

1. Enter Programming Mode: installer code + 8-0-0.

2. Change the default Installer Code using field ∗20.

3. Enter the appropriate central station phone numbers and account numbers.

4. Program the system data field options as desired.

4. Use the various menu modes to program zones, relay outputs, descriptors, etc.

5. If AVS system is installed, use the appropriate AVS Quick Program Command.

6. Program Schedules (if used): Master code + [#] + 64

7. Enable RF button keyfobs (if used) and assign to user numbers accordingly.

8. Show the Master user how to change the default Master code:

master code + [8] + 0-2 + new code + new code again

5. Test the System.

1. Disarm; the system and close all protected windows, doors, etc.

2. Enter the Master code + [5] (TEST), then press [0] (walk).

3. Listen. The external sounder should sound for about 1 second then turn off.

4. Fault zones in turn and listen for three beeps from the keypad. ID of each faulted point should appear

on the display. The display clears when the zone is restored.

5. Walk in front of any interior motion detectors and listen for three beeps. The identification of the detector

should appear on the display when it is activated.

6. Test all smoke and CO detectors, following the manufacturer's instructions. The identification of each

detector should appear on the display when activated.

7. When all protection points have been checked and are intact (closed), there should be no zone

identification numbers displayed on the keypad.

8. Exit test mode: security code + [1] (OFF)

100 mA

300 mA

500 mA

600 mA

450ft (137m)

150ft (46m)

90ft (27m)

75ft (23m)

700ft (213m)

240ft (73m)

140ft (43m)

120ft (37m)

1100ft (335m)

350ft (107m)

220ft (67m)

170ft (52m)

1500ft (457m)

550ft (168m)

350ft (107m)

270ft (82m)

[see instructions K5305-1V7 or higher])

Communication Device (7847i, 7845GSM, 7845i-GSM)

• Set the communication device to address 03.

• Use ∗29 Menu mode to enable and program the device.

AVS System

• If used, follow the installation instructions provided with the module.

• Connect the AVS module to the control's ECP terminals and connect all other ECP devices to the

AVS module's ECP terminals.

• Set the AVS address using its DIP switches: V15P = 08; V20P = 11

• Use the desired AVS Quick Program Command to set pre-defined options:

installer code + 0-3: enable AVS operation

installer code + 0-4: enable AVS and enable panel sounds on AVST speaker

• Use field ∗55 Dynamic Signaling Priority to select the desired reporting paths.

2. Connect hardwire zones to the appropriate zone terminals 8-20.

3. On-Board Trigger Connections

• Connect field wiring to the appropriate trigger pin using the SA4120XM-1 cable (if using 1361X10

transformer) or the 4-wire cable supplied (N4632-4).

• Trigger outputs are normally high, and go low upon programmed condition.

• Outputs can be set for inverted operation (low, go high) using *79 Menu mode.

• Use ∗79/∗80 Menu modes to program the trigger outputs.

4. Install Wireless Zone Transmitters.

• Use ∗56 Menu mode to program wireless zones and enroll the transmitters.

• Use the Go/No Go Test mode to verify adequate signal strength from each transmitter location: With

system "Ready to Arm," enter Installer code + [#] + 4, then fault each transmitter and listen for 3

beeps at the keypad and the zone display. Exit mode: user code + [1] (OFF).

5. Connect the external sounder to terminals 3 and 4.

• If supervised output desired, see Sounder Supervision wiring diagram on reverse side, and set field

∗91 Option Selection for Bell Supervision.

6. Connect the phone line using terminals 21-24.

• Use an RJ31X jack as shown in the diagram on reverse side.

Major Features and Capacities

Feature

VISTA-20P

Partitions

2 plus common area

Zones

48 plus 16 keyfob zones for

total of 64 zones:

• 8 hardwired zones (1-8)

• Up to 40 additional wired

zones (9-48) using up to 5

4219/4229 modules

• Up to 40 wireless zones

(5800 series; zones 9-48)

• 4 configurable zone types

Security Codes

Schedules

Keypad macros

Event Logging

100

Paging

Keypads

Touch Screen Devices

4219, 4229

4204

Output Relays / X-10 devices

On-Board Triggers

Output Functions

WARRANTY INFORMATION

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa

VISTA-15P

not partitioned

32 zones plus 8 keyfob zones

for total of 40 zones:

• 6 hardwired zones (1-6)

• Up to 16 additional wired

zones (9-24) using up to 2

4219/4229 modules

• Up to 26 wireless zones

(5800 series; zones 9-34)

• 2 configurable zone types

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747