Great World GW-6078TBT Kullanım Kılavuzu - Sayfa 3
Elektrikli Isıtıcı Great World GW-6078TBT için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Great World GW-6078TBT 7 sayfaları.
Sayfayı Yazdır
Remote Control Battery Installation
1. Pull out the battery holder from
2. Place cell battery in the battery holder
the bottom of the remote control.
with "+"(positive) mark face up to
correspond the "+" mark on the battery
holder, then push it into the remote
control.
Remote Control Function
Remote Control
Reminder: There are 2 indicators at the right side of control panel, when
the heater has its initial use and heater function is set at the high level,
both L and H indicators will light up; when the heater is set at the low level,
only L indicator will light up. This model has thermostat function,when the
environment temperature reaches the desired temperature, heater will shut
down automatically; however, the indicator will still light up to let users
know the heater mode is still active, not the current heater working level.
-There are six(6) buttons on the remote control and six(6) corresponding
buttons on the control panel of the electric fireplace insert.
1. [POWER(
or )] turns the electric fireplace insert either on or off.
When the heater is off, press this button once to turn the heater on;
press it again to turn the heater off.
2.[DIMMER(
or
)] controls the brightness of flame and lo g, there are 5
levels. When heater is turned on the first time, flame and log is at their
brightest level. Press the button and the brightness of the logs will begin
to change, from the brightest level to the weakest level. The
corresponding digital display will blink
If there is no other operation, digital display will go back to default
temperature setting and show environmental temperature.
3.[HEATER(
or
)] controls the heating element. Press once, the heat
3. Assembly complete.
Receiver
Digital Display
Low heat level Indicator
High heat level Indicator
Bluetooth connection Indicator
UP
DOWN
Control Panel
,
, , ,
for a period of time.
is at the high level, H and L indicator will both light up; press
again, the heat is at the low level, L indicator will light up; then
press again, heat stops, and heating element is turned off,
both H and L indicator are off.
4. [TIMER(
or
)] is the timer setting button. Press once, the digital
display will blink which indicate the time can be entered, so touch [UP]
or [DOWN] button may increase or decrease the time in between 0-12
hours.
5. [UP(
or
)] increases the time and temperature. When the mode is at
UP
timer setting, press once, the digital display will increase by 0.5(half)
hour. Long press this button, time will go up continuously. The options
are between 0-12 hours; when the mode is at temperature setting, press
once, temperature will increase by 1
temperature will go up continuously. The options are between
℉
℉
60
-97
.
6. [DOWN(
or
)] decreases the time and temperature. When the mode
DOWN
is at timer setting, press once, the digital display will decrease by
0.5(half) hour. Long press this button, time will go down continuously.
The options are between 12-0 hours; when the mode is at temperature
setting, press once, temperature will decrease by 1
button, temperature will go down continuously. The options are between
℉
℉
97
-60
.
7. [
] indicates the Bluetooth connection is successfully paired if the
indicator is on. Refer to the operation manual in the APP to continue.
Other Important Features
8. To protect the heater, the fan will continue turning for quite a few
seconds after heater is shut down.
9. When the [POWER] is firstly turned on, only the flame and log work; to
have the heat to blow out, you have to press [HEATER]. Other than
[POWER] button, all other operation button will function when the power
is turned on.
10. If the temperature inside of the electric fireplace insert becomes
abnormally high, the temperature protection mechanism will turn on
automatically and the heater will be shut down within a few seconds (fan
will be stopped in around 15 seconds of retardation). Any operation are
prohibited. Please remove the power cord from outlet and wait a few
minutes for heater to cool down or till temperature protection mechanism
reconnect, then plug in the power cord to resume the condition before
the abnormality of the electric heater.
Temperature setting and operation
℉
. Long press this button,
℉
. Long press this