Dynafile 14010 Manuel - Sayfa 2
Araçlar Dynafile 14010 için çevrimiçi göz atın veya pdf Manuel indirin. Dynafile 14010 12 sayfaları. Air tool
Sayfayı YazdırWMV-Dresden, Ersatzteilservice für Elektrowerkzeuge, Motor- und Gartengeräte
• Keep hand and clothing away from working end of the air tool.
• Be sure that any loose clothing, hair and all jewelry is properly restrained.
• Secure inlet bushing on air tool with a wrench before attempting to install the air fitting to avoid damaging housing assembly.
• Check tool RPM (speed) with tachometer with air pressure set at 90 PSIG while the tool is running. If tool is operating at a higher speed than the RPM marked on the tool
housing, or operating improperly, the tool must be serviced and corrected before use.
Caution: Tool RPM must never exceed abrasive/accessory RPM rating. Check accessory manufacturer for details on maximum operating speed or special
mounting instructions.
• Disconnect air hose from tool when changing belts and contact arms.
• Connect air tool to power source. Be careful NOT to depress throttle lever in the process. Do not expose air tool to inlet pressure above 90 PSIG or (6.2 Bars).
Caution: After installing the accessory, before testing or use and/or after assembling tool, the Dynafile
Gradually increase tool speed. DO NOT USE if tool vibration is excessive. Correct cause, and retest to insure safe operation.
• Make sure that work area is uncluttered, and visitors are at a safe range from the tools and debris.
• Use a vise or clamping device to hold work piece firmly in place.
• Do not apply excessive force on tool or apply "rough" treatment to it.
• Always work with a firm footing, good posture and proper lighting.
• Make sure that work area is uncluttered, and visitors are at a safe range from the tools and debris. Potentially explosive atmospheres can be caused by dust and fumes
resulting from sanding or grinding. Always use dust extraction or suppression systems which are suitable for the material being processed.
Report to your supervisor any condition of the tool, accessories, or operation you consider unsafe.
Contact Arm Assembly/Disassembly Instructions
11275 CONTACT WHEEL SHAFT
1
REMOVAL TOOL
PRESS FIT
SLIP FIT
11271 WHEEL POSITION BLOCK
REMOVE CONTACT ARM FROM MACHINE.
PRESS CONTACT WHEEL SHAFT OUT OF CONTACT ARM.
11279 CONTACT WHEEL SHAFT
4
ADHESIVE
PIPE CLEANER
BORE OF BEARING
BEARING
MOISTEN TIP OF PIPE CLEANER WITH CONTACT WHEEL
SHAFT ADHESIVE AND APPLY TO ID OF BEARINGS BEFORE
INSTALLING PROPER SHAFT.
DO NOT GET ADHESIVE ON FACE OF BEARING.
1
With your thumb, pull and slide
guard open in a clockwise direction.
4
Slip belt over contact wheel. Release
idler arm lever. Operate on the contact
wheel or on the return side of the belt.
OPERATING INSTRUCTIONS (continued)
2
REMOVE OLD BEARING FROM WHEEL
5
CONTACT WHEEL SHAFT
SLIP FIT
PRESS
INSERT INTO
FIT HERE
INSTALL NEW SHAFT
Abrasive Belt Exchange Instructions
2
Form a loop in belt keeping the belt splice
between fingers as shown in photo above.
Slip lower loop of belt under the drive wheel.
5
Completely close the guard.
®
must be started at a reduced speed to check for good balance.
11276 BEARING REMOVAL TOOL
3
FOR 1/4" ID CONTACT WHEEL
11277 BEARING REMOVAL TOOL FOR
3/8" ID CONTACT WHEEL
CONTACT WHEEL
11271 WHEEL POSITION BLOCK
11271 WHEEL POSITION BLOCK
2
11274 CONTACT WHEEL BEARING
MOUNT TOOL
CONTACT WHEEL
PRESS BEARING INTO EACH SIDE OF WHEEL
3
Depress idler arm lever and pull belt
toward the contact wheel.