2gig Technologies 2GIG-PIR1-345 Kurulum Talimatları - Sayfa 2

Güvenlik Sensörleri 2gig Technologies 2GIG-PIR1-345 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. 2gig Technologies 2GIG-PIR1-345 4 sayfaları. Passive infrared motion detector

Sayfayı Yazdır

Step 3: Powering ON the PIR

With the battery inserted (see "Inserting and Replacing the Battery"

on page 1), press and release the switch labeled TAMPER. It takes

approximately 10 seconds for the PIR to power ON.

Mounting the PIR

There are two methods for mounting the PIR: Option A: Bracket

Mounting or Option B: Direct‐to‐Wall Mounting. For both methods,

always mount the PIR at a height of 7.5 ft (2.3 m).

Figure 3 PIR and Mounting Bracket Detail

A PIR

B Plastic Mounting Bracket

C Plastic Wall Mount

D Plastic Corner Mount

Option A: Bracket Mounting

See Figure 3 PIR and Mounting Bracket Detail. If you plan to mount

the PIR to either the Plastic Wall Mount or Plastic Corner Mount, you

must first attach the Plastic Mounting Bracket to the PIR backplate.

Step 1: Attaching the Plastic Mounting Bracket to the PIR

Remove the PIR backplate.

Insert the two stubs on the Plastic Mounting Bracket into the

corresponding holes on the exterior side of the PIR backplate.

On the interior of the PIR backplate (see Figure 4 PIR Backplate—

Direct‐to‐Wall Mounting Guides), use the Short Phillips Head

Screw (provided) to secure the Plastic Mounting Bracket to the

backplate

Replace the PIR backplate.

Reattach the screw that was removed earlier to the bottom of the

PIR.

Continue with either Step 2: Wall Mounting Option or Step 2:

Corner Mounting Option.

For optimum pet immunity when using the Plastic

NOTE:

Mounting Bracket, ensure that the PIR is mounted to the wall

or corner with NO tilt (see "Lens Pattern and Tilt Angles" on

page 3).

Step 2: Wall Mounting Option

See Figure 3 PIR and Mounting Bracket Detail. If using the Plastic Wall

Mount (C), do the following:

NOTE:

Ensure that you have attached the bracket to the PIR

backplate (see Step 1: Attaching the Plastic Mounting Bracket

to the PIR).

On the intended wall, use the two (2) Plastic Wall Anchors to hang

the Plastic Wall Mount at a height of 7.5 ft (2.3 m).

Locate the barrel end of the Plastic Mounting Bracket. Locate the

barrel end of the Plastic Mounting Bracket and carefully set it onto

the ribbed pin of the Plastic Wall Mount at the desired angle (see

Lens Pattern and Tilt Angles on page 3).

From the topside of the Plastic Wall Mount, use the Short Phillips

Head Screw with Fender (provided) to secure the mount to the

barrel end of the bracket.

Step 2: Corner Mounting Option

See Figure 3 PIR and Mounting Bracket Detail. If using Plastic Corner

Mount, do the following:

Ensure that you have attached the bracket to the PIR

NOTE:

backplate (see Step 1: Attaching the Plastic Mounting Bracket

to the PIR on page 2).

Use the two (2) Plastic Wall Anchors to hang the Plastic Corner

Mount at a height of 7.5 ft (2.3 m).

Locate the barrel end of the Plastic Mounting Bracket and carefully

set it onto the ribbed pin of the Plastic Wall Mount. Ensure that

you set it at the desired angle (see "Lens Pattern and Tilt Angles"

on page 3).

From the topside of the Plastic Wall Mount, use the Short Phillips

Head Screw with Fender (provided) to secure the mount to the

barrel end of the bracket.

Option B: Direct-to-Wall Mounting

If planning to mount the PIR directly to a wall, use the built‐in

mounting guides on interior of the PIR backplate to screw the

backplate into the wall.

Remove the PIR backplate.

Use the two (2) Plastic Wall Anchors to screw the PIR backplate

into the wall at a height of 7.5 ft (2.3 m):

• Wall. Use the wall mounting guides (see A below).

• Corner Mount. Use the left‐ or right‐ corner mounting guides

(see B below).

Figure 4 PIR Backplate—Direct-to-Wall Mounting Guides

A Wall Mounting Guides (For Option B: Direct‐to‐Wall Mounting)

B Corner Mounting Guides (For Option B: Direct‐to‐Wall Mounting)

C Wall Mount Bracket Guide (For Option A: Bracket Mounting)