GreatWhite GW9500 Kullanıcı El Kitabı - Sayfa 6

Yüzme Havuzu Vakumu GreatWhite GW9500 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. GreatWhite GW9500 12 sayfaları. Automatic pool cleaner

Sayfayı Yazdır

ABOUT THE CLEANER AND ACCESSORIES:

Swivel assembly (Figure 9)

Installing the swivel assembly is a snap.

Just insert it into the cleaner body and

give it a quarter turn.

If you attach a unidapt handle to the

swivel for manual vacuuming, be sure it

is the special, floating unidapt handle

Figure 9

provided with the cleaner (Replacement

Part No. GW9019). Use of a different

unidapt handle will hinder the cleaner's performance.

Hoses (24' and two 8' lengths – Figure 10)

The unit includes a 24' hose and two 8'

extensions. Do not cut any of these

hoses.

The best hose length is at least 4'

longer than the distance from your

suction source (whether skimmer or

dedicated suction line) to the furthest

24'

point in the pool. If the hose seems to

be too long, remove the 8' section pro-

vided. Do not cut the 24' hose.

Be sure to connect the tapered end of

the 24' hose (marked "connect to clean-

er") to the cleaner head.

Figure 10

1883 0795

If additional hose is needed, use only

the specially designed 8' extension hose from your Sta-

Rite dealer (order replacement part No. GW9511). Use

of another manufacturer's hose will hinder cleaner cov-

erage (this also holds true for the 24' hose). If you need

to replace the 24' hose, buy only the original equipment

hose (order replacement part No. GW9525).

Bumper Inserts (see Key 2A, Page 10) help to make the

cleaner more buoyant to allow better access to the

shallow end of the pool. Do not install inserts from the

top; they will become jammed and not work properly.

Only install inserts from the bottom.

If the bumper on the cleaner appears to lift the cleaner

to the surface of the pool, check for trapped air in the

Hose ( 6" connector ) female x female (purchase acces-

sory No. GW9021) If required, this will accommodate a

male x male connection at the skimmer.

Reducer cone (Figure 11)

Figure 11

Automatic vacuum regulator (Figure 12)

ment with severe personal injury or drowning.

sory bag is for systems with extremely high vacuum.

Use of this cap will help prevent the cleaner from

"walking" out of the pool.

Make sure the vacuum regulator, especially the black

rubber cap, is submerged at all times. If not, the pump

will suck air through the regulator and lose prime. This

could damage the pump.

ABOUT BUMPER INSERTS

The reducer cone is required to make

most hose connections. When used, it

will keep the hose in place if the filter

system is stopped.

Hazardous suction. Can cause entrap-

Vacuum regulator should be installed in all

situations. If the cleaner moves very slowly

or not at all (indicating low vacuum in the

system), see Troubleshooting Chart, Page 7.

The regulator includes two black rubber

regulator caps. One is installed on the regu-

lator at the factory, and one is in the acces-

Figure 12

sory bag. The cap marked "50" in the acces-

cleaner and hose. If no air is found, remove one

bumper insert block and watch and see if the cleaner

remains submerged and on the pool floor while work-

ing. If not, remove individual insert blocks as needed

until the cleaner rests on the pool floor and operates

properly.