Dynakit MArk IV Montaj Talimatları - Sayfa 4

Amplifikatör Dynakit MArk IV için çevrimiçi göz atın veya pdf Montaj Talimatları indirin. Dynakit MArk IV 16 sayfaları.
Ayrıca Dynakit MArk IV için: Montaj Talimatları (12 sayfalar)

Refer
WIRING INSTRUCTIONS
/
Connect one of the black power transfor-
mer leads to lug #2 of the slide switch
(8).
Connect the other black lead to lug
B
of the fuse post
(8).
Connect one yellow power transformer
lead to pin #2 of socket V 1
(8).
Con-
nect the other yellow lead to pin #8 of
socket VI.
the hole near the four screw terminal
strip. Use #8 hardware to secure the
transformer.
Mount the quadruple section filter ca-
pacitor in the special cutout. Observe the
symbols at the base of each connecting
lug. These should be oriented as shown
in the pictorial. Fasten the capacitor by
giving each of the mounting lugs a quar-
ter turn while holding the capacitor
snugly against the chassis.
Twist the two red leads together and
position them around socket VI. Con-
nect one red lead
to
pin #4
(8).
Con-
nect the other red lead to pin #6 of
VI
(8).
Twist the two green power transformer
leads together and position them to
socket V2. 8EE PICTORIAL. Connect
one green lead to pin #2 of socket V2,
and the other green lead to pin #7 of V2.
Connect the green/yellow lead to lug #2
of the five lug terminal strip.
Connect the red/yellow lead to solder
lug at the mounting screw of the five
lug strip,
Connect the red/black lead to lug #4 of
the five lug strip.
Connect one choke lead to Jug #1 (semi-
circle) of the quad filter capacitor. Con-
nect the other choke lead to lug #2 of
the filter capacitor.
Connect the black lead of the A-470
output transformer to lug #
I
of the four
screw terminal strip. Connect the brown
lead to lug #2 (8). Connect the orange
lead to lug #3 (8). Connect the yellow
lead to lug #4.
Connect the red output transformer lead
to lug #2 of the filter capacitor. Twist
the remaining leads together and carry
them
to
sockets V2 and V3. 8EE PIC-
TORIAL. Connect the blue/white lead
to pi n #3 of socket V2 (8). Connect the
green/white lead
to
lug #4 of socket V2
-
(~
)
(-J;
4
2
7
5
9
6
3
8
10
Each length of hookup wire specified should have
approximately
%"
of insulation 'stripped from each
end unless otherwise specified. Transformer leads
may be trimmed as required for a neat wiring job.
1
( j )
12
MECHANICAL ASSEMBLY
Pictorial Diagrams for Location of Parts
Mount the four octal sockets with #4
screws, nuts, and lockwashers (the small-
est screws supplied). Note that there is
a small slot or keyway in the center hole
of each socket; be sure in each instance
that this keyway is properly oriented as
shown in the pictorial diagrams. Insert
the screws from the top of the chassis and
mount the sockets from the inside. Fasten
each screw with a nut and lockwasher.
Mount the input socket from the inside
of the chassis using #4 screws, nuts, and
lockwashers.
Using #4 hardware, mount the four screw
terminal strip on the outside of the
chassis.
Mount the slide switch from the inside
with #4 screws. Nuts and lockwashers
are not necessary in this instance. Follow
the position of the connecting lugs in the
pictorial.
Mount the fuse post with the special nut
provided. The rubber bushing goes on the
outside of the chassis. Note that there is
only one correct way for the post to be
mounted.
Insert the rubber grommet in the
%"
hole
at the end of the chassis.
Mount the 10,000 ohm bias potentiometer
in the
%"
hole near the pair of octal
sockets. Put the lockwasher on the shaft,
insert the control in the hole and fasten
at the top of chassis with the
%"
nut.
Note orientation of connecting lugs.
Mount the five lug terminal strip and the
solder lug at the center of the chassis.
Insert a #4 screw from the outside. Place
the terminal strip over the screw, then
the small solder lug, then the #4 nut.
With #4 hardware, mount the cable
clamp loosely near the single octal socket.
Feed all the wires of the power trans-
former, PA-135, through the single hole
provided.
Fasten the transformer in
place with two #8 screws in the holes
nearest the front of the chassis using #8
lockwashers and nut<>. Now, from the
bottom, place the choke over the remain-
ing two transformer mounting holes and
fastcn both in place with two more sets of
#8 hardware. All but the black trans-
former leads go under the cable clamp
next to the rectifier socket; and then this
clamp may be tightened.
Mount the output transformer, A-470, on
the remaining set of holc-t; at the center of
the chassis. Note that the black, brown
orange, and yellow leads come through
(J )
( )
9
7
6
2
4
5
8
1
3
11
10
2