HID iCLASS RK40 Kurulum Kılavuzu - Sayfa 2

Kart Okuyucu HID iCLASS RK40 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. HID iCLASS RK40 2 sayfaları.
Ayrıca HID iCLASS RK40 için: Kurulum Kılavuzu (13 sayfalar), Kurulum (2 sayfalar)

Sayfayı Yazdır
HID iCLASS RK40 Kurulum Kılavuzu
Installation Guide
iCLASS Reader Models RK40 & RWK400
3- Install Mounting Plate
Attach the mounting plate onto the back box or a wall surface. Dimensions are in inches (centimeters).
0.156 /
2.000 /
4.490 /
0.40 cm
5.08 cm
11.40 cm
1.650 /
3.280 /
4.19 cm
8.33 cm
0.220 / 0.56 cm
4- Connecting
Serial Port (Model RWK400 Only)
8 Pin Terminal
Function
1
Ground
2
Y / RS-232 TX
3
Z
4
Ground
5
RS485B / RS-232 RX
6
RS-485A
7
Ground
8
DC+
1
Optional Connections
2
Drain wire can be used for data return line when a separate power supply is used.
3
+DC, Return & Drain wires are common between the Wiegand and Serial Ports.
4
In RS-485 mode, pin 2 must be connected to pin 6 and pin 3 must connected to pin 5 with jumpers at the connector.
5- Testing
A.
Turn Power On – Watch the sign-on LED and hear the speaker tone sequences.
Read Card – Present a valid card to the reader and verify the visual and audio feedbacks.
B.
6- Mounting
Reverse the procedure in step 1 to attach the unit to the mounting plate.
Optional Features
RS232/485 interface/Host Mode - for applications requiring a serial link. See Protocol Document 6090-902 for information
Open Collector Output – controls an external device (13.8VDC Max). See iCLASS Application Note for details
Configuration Options - Configure LED, Speaker, and other features. See How To Order Guide or iCLASS Application Note for details
Hold Input – when asserted, this line either buffers a card read or disables a card read until released, as configured.
FCC WARNING:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation. For proper regulatory compliance, the drain wire
should be disconnected at the power supply end of the cable. The reader is intended to be powered from a limited power source output of a previously certified
power supply. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
An ASSA ABLOY Group company
_____________________________________________________________________________________________________
HID Corporation 9292 Jeronimo Road Irvine, CA 92618-1905 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690
Web page - www.hidcorp.com e-mail – [email protected] iClass Keypad Reader Install Manual 6094-901 Rev A
2.000 / 5.08 cm
0.355 / 0.90 cm
1.650 / 4.19 cm
0.175 / 0.44 cm
0.300 /
0.110 / 0.28 cm
0.76 cm
MOUNTING PLATE
10 Pin Terminal
1.550 / 3.94 cm
1.550 /
3.94 cm
OPTIONAL SPACER
Wiegand Port (Models RK40, RWK400)
Color-coded Pigtail
10
Violet
9
Blue
8
Yellow
7
Drain
6
Brown
5
Orange
4
White
3
Green
2
Black
1
Red
1.000 / 2.54 cm
0.080 / 0.20 cm
1.130 /
2.87 cm
Function
1
Open Collector
1
Hold
1
Speaker
2
Shield Ground
1
Red LED
1
Green LED
Data 1
Data 0
Ground
3
+DC (10-16 VDC)
ASSA ABLOY
Page 2 of 2