Celestron ASTRO FI 22202 Kullanım Kılavuzu - Sayfa 6

Teleskop Celestron ASTRO FI 22202 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Celestron ASTRO FI 22202 12 sayfaları. 90 mm refractor/102 mm maksutov/130 mm newtonian

Sayfayı Yazdır

1. What's in the Box

ALIGNING THE STARPOINTER FINDERSCOPE

The ﬁ rst time you assemble your telescope, you'll need to align the StarPointer ﬁ nderscope with the main optics of the

telescope. This step can be done without powering on the telescope. Although this step can be done out in the ﬁ eld

at night, it is signiﬁ cantly easier to accomplish this outdoors in daylight. Once you have completed the ﬁ nderscope

alignment, you should not have to repeat this step unless the ﬁ nderscope is bumped or dropped.

1. Take the telescope outside during the day and, using your naked eye, ﬁ nd an easily recognizable object, such as

a streetlight, car license plate, or tall tree. The object should be as far away as possible, but preferably at least a

quarter mile away.

2. Remove the main dust cover from the front of the telescope by pulling it straight off. Make sure your 25 mm eyepiece

is installed in the focuser.

3. Do not try to move the telescope left and right while it is off. Move the assembled tripod so the telescope is pointed

in the direction of the object you chose in step 1.

4. Look through the telescope and move it up and down until the object you chose lies in the center of the view. If the

image is blurry, gently turn the focus knobs on either side of the telescope until it comes into sharp focus.

NOTE:

The image you see in the eyepiece will appear mirror reversed. This is perfectly normal in an astronomical telescope.

5. Once the object is centered in your 25 mm eyepiece, turn on

the Red Dot Finder by rotating the power switch knob on the

right side of the ﬁ nder clockwise. You will hear an audible click

to conﬁ rm that the ﬁ nder has been turned on. This knob also

controls the brightness of the red dot. Turn the knob all the way

to the end to make the dot as bright as possible.

6. With your head positioned about a foot behind the ﬁ nder, look

through the round window of the ﬁ nder and locate the red dot.

It will probably be close to, but not on top of, the object you see

when you are looking through the 25 mm eyepiece.

7. Without moving the telescope, use the two adjustment knobs

located on the side and underneath the StarPointer ﬁ nderscope

(Figure 8). One controls the left-right motion of the dot. The

other controls the up-down motion of the dot. Adjust both until

the red dot appears over the object you are observing in the

25 mm eyepiece.

Your StarPointer Finder is now aligned!

NOTE:

Be sure to turn off the Starpointer Finder when not in use to conserve battery power.

GET READY TO OBSERVE

Now that your telescope is assembled and the StarPointer is aligned, let's connect it to your smartphone or tablet.

We recommend you familiarize yourself with the telescope and app during the day before using it at night.

CAUTION:

Remember to never point the telescope at the Sun during the day without using a proper full aperture solar filter!

1. Plug the battery pack into the power port on the base of the telescope, (Figure 9). The red WiFi light on the arm will light,

indicating power and WiFi-ready status. Make sure the small switch near the power socket is in the RIGHT position as

shown in the ﬁ gure.

2. Go to your device's WiFi settings, and connect to the "Celestron-xx" network. Wait for your device to conﬁ rm that you

have successfully connected.

| ENGLISH

A s t r o F i T E L E S C OP E

Power/Brightness Knob

Up/Down

Adjustment Knob

Left/Right

Adjustment Knob

Fig. 8