AutomationDirect CLICK C0-08TR-3 Manuel

Kontrol Ünitesi AutomationDirect CLICK C0-08TR-3 için çevrimiçi göz atın veya pdf Manuel indirin. AutomationDirect CLICK C0-08TR-3 3 sayfaları. Expansion i/o module

AutomationDirect CLICK C0-08TR-3 Manuel
C0-08TR-3 CLICK Expansion I/O Module
Please read and understand the information in this
insert prior to installation, operation, or servicing
this equipment.
Please refer to the CLICK User
C0-08TR-3
General Specifications +
Operating Temperature
Storage Temperature
Relative Humidity
Environmental Air
Altitude
Agency Approvals
+ Keep out iron powder, moisture, oil or chemicals. Isolate from shock or vibration, direct sunlight, and from electric or ferromagnetic field.
* Meets EMC and Safety requirements. See the Declaration of Compliance for details.
Copyright© 2020, Automationdirect.com Incorporated/All Rights Reserved Worldwide
www.automationdirect.com/click-plc
General Safety
In this Insert Sheet, the safety instruction levels are classified into "WARNING" and "CAUTION"
• Don't use this equipment in a flammable or explosive environment in order to avoid accidental injury or fire.
• You should use external electromechanical devices that are independent of the PLC (Programmable Logic
• When using this product, connect it to the Click CPU unit.
• Please make sure that you earth the Ground terminal of the Power Units for CLICK CPU
• Don't operate the equipment with a nonconforming external power supply to avoid electric shock,
• Don't intentionally fault wiring; this may cause equipment damage or fire.
• To avoid electric shock or malfunctions which might result in an accident, don't touch any terminal while
• Don't put metals (e.g. Screwdriver) into radiator holes, drop trash, or foreign objects (e.g. cut-off wire) into
• If the equipment is used in a manner not specified by the manufacturer, the protection provided by the
• Use and store the equipment in an environment described in the specifications (regarding temperature,
• Ensure all wiring has strain reliefs in order to avoid damage to insulation which might result in electric shock
• Ensure secondary external power circuits are only live after PLC control program is started. Otherwise a
• Don't block the radiator holes. This may cause an increase of internal temperature resulting in equipment
• Don't disassemble or modify the equipment so as to avoid electric shock, equipment damage or fire.
• Cut off all phases of the external power source before maintenance work, thus avoiding electric shock or
32° to 131°F (0° to 55°C)
-4° to 158°F (-20° to 70°C)
30% to 95% (non-condensing)
No corrosive gases permitted (Level 2 environmental pollution)*
Up to 2000m
UL61010-2-201
CE (EN61131-2):2007*
RoHS (2011/65/EU) and amendment (EU) 2015/863
Manual
(C0-USER-M)
for
(https://cdn.automationdirect.com/static/manuals/
c0userm/c0userm.html).
Assumes that incorrect handling may cause hazardous conditions, resulting in
WARNING
severe injury or death.
Assumes that incorrect handling may cause hazardous conditions, resulting in
CAUTION
medium or slight injury, or may cause equipment damage.
Controller) system to provide protection for any part of the system. Otherwise, malfunction or output
failures may result in a hazardous accident.
(C0-00AC/01AC) to avoid electric shock or equipment damage during a short circuit.
equipment damage or fire.
the PLC power is on.
the device, in order to avoid electric shock or equipment damage.
equipment may be impaired.
humidity, vibrations, shock, etc.) in order to avoid equipment damage or fire.
or fire.
malfunction or output failure may result in a hazardous accident.
damage or fire.
equipment damage.
CLK-1
more
information
Please follow the instructions below for personal and operational safety.
WARNING
CAUTION
Output Specifications
Outputs per Module
Peak Voltage
Operating Voltage Range
Output type
AC Frequency
Maximum Output Current
Minimum Load Current
Maximum Inrush Current
OFF to ON Response
ON to OFF Response
Status Indicators
Commons
Bus Power Required (24V)
CLICK Module Insert
3505 HUTCHINSON ROAD
CUMMING, GA 30040-5860
8
30VDC; 264VAC
6–27 VDC;6–240 VAC
8 Relays, FORM A (SPST)
47–63 Hz
3A / point
6A / common
5mA @ 5VDC
5A for 10ms
< 15ms
< 15ms
Logic Side (8 points, red LED)
Power Indicator (green LED)
4 (2 point / common)
Max. 90mA (all points ON)
1-800-633-0405