ActiveProducts XE06 Kullanıcı El Kitabı - Sayfa 9

Basınçlı Yıkama ActiveProducts XE06 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. ActiveProducts XE06 10 sayfaları. 1600 psi electric pressure washer

Sayfayı Yazdır

TROUBLESHOOTING

Disconnect the machine from the power source before making any repairs.

Symptom

Cause

Motor will not start.

On/Off switch is in the

"OFF" (O) position.

Power cord is not plugged in.

Extension cord is too long.

Extension cord is not

proper gauge.

Extension cord is damaged.

Electrical outlet does not

supply adequate power.

Tripped pressure washer

circuit breaker

Unit does not reach

Diameter of garden hose is

high pressure.

too small.

Water supply is restricted.

Not enough water supply.

Water inlet filter is clogged.

Power nozzle is in low-

pressure position.

Pump is sucking air.

Output pressure varies high

Not enough inlet water supply. Turn water on fully. Check

and low.

Pump is sucking air.

Water inlet filter is clogged.

Solution

Turn switch to the "ON"

( | ) position.

Plug in power cord.

Replace extension cord

with either a 25' (7 .6 m)

14AWG cord or a 50' (15 m)

14AWG cord.

Try a different outlet.

Allow to cool, and restart unit.

Replace with a 1" (25 mm) or

5/8" (16 mm) garden hose.

Check garden hose for

kinks, leaks and blockage.

Open water source fully.

Remove filter and rinse in

warm water.

Turn power nozzle to high-

pressure position.

Check that hoses and

fittings are airtight. Turn

"OFF" machine, and purge

pump by squeezing trigger

gun until a steady flow of

water emerges through

the nozzle.

garden hose for kinks, leaks

or blockage.

Check that hoses and

fittings are airtight. Turn

"OFF" machine, and purge

pump by squeezing trigger

gun until a steady flow of

water emerges through

the nozzle.

Remove filter and rinse

with warm water.

TROUBLESHOOTING

Symptom

Cause

Output pressure varies high

Discharge nozzle is obstructed.

and low. (continued)

Calcified gun, hose or

power nozzle.

Detergent not working.

Detergent container is empty.

Detergent bottle or suction

tube not properly connected.

Detergent is too thick.

Filter on detergent suction

tube is clogged.

Nozzle is in high-pressure

position.

Discharge nozzle is obstructed.

Garden hose connection leaks.

Loose fittings.

Missing/worn rubber washer.

Spray wand, extension, or

Broken o-ring or plastic insert.

nozzle leaks.

Pump is noisy

Pump is sucking air

Water filter is clogged.

Water leaks from pump (up

Loose fittings.

to 10 drops per minute

is permissible).

Water seals are damaged

or worn.

Oil is dripping

Oil seals are damaged or

worn.

Solution

Blow out or remove debris

with a fine needle.

Run distilled vinegar

through detergent tank.

Add more detergent.

Check connections.

Dilute detergent.

Run warm water through

filter to remove build-up.

Turn nozzle tip to

low-pressure position.

Blow out or remove debris

with a fine needle.

Tighten fittings.

Insert new washer.

Call the Toll-Free Hotline.

Check that hoses and fit-

tings are airtight. Turn off

machine and purge pump

by squeezing trigger gun

until a steady flow of water

emerges through the nozzle.

Remove water filter and

rinse in warm water.

Check that all fittings are tight.

Call the Toll-Free Hotline