ADEMCO 4192 Kurulum Talimatları

Duman Alarmı ADEMCO 4192 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. ADEMCO 4192 4 sayfaları. Smoke detector base/transponder

Sayfayı Yazdır
ADEMCO 4192 Kurulum Talimatları
s:
MARGIN
LINES
INDICATE
PRINCIPAL
CHANGES
IN THIS l/88 ISSUE
*
GENERAL
INFORMATION:
WIRING
THE
No. 4192
The ADEMCO
No. 4192
PLUG-IN
SMOKE
DETECTOR
BASE is a
VECTOR
POINT
PROTECTION
SECURITY
SYSTEM
component.
It IS
intended
for use with interchangeable
UL Ltsted detector
heads,
Model
BK-2851
B (PHOTOELECTRIC);
Model
BK-2851
BTH (PHOTOELECTRIC
WITH BUILT-IN
THERMOSTAT)
and Model
BK-1851
B (IONIZATION).
The
base can be installed
on a standard
ceiling
mount
electrical
box and both
the base and the detector
are powered
through
the polling
loop.
IMPORTANT!
The instructions
which
accompany
the aforementtoned
detector
heads
only parttally
pertatn
to the No. 4192 SMOKE
DETECTOR
BASE/TRANSPONDER.
The relevant
sections
are: Preface;
Specifica-
tions;
SENSITIVITY
TESTING
AND
MAINTENANCE,
TAMPER-
PROOF
FEATURE,
and LIMITATIONS
OF SMOKE
DETECTORS.
All wrring
must be installed
in compliance
wrth the National
Electrical
Code
and with all local codes.
For complete
lnformatton
regardrng
the polltng
loop, refer
to the instructions
which
accompany
the control
panel.
The followmg
diagram
illustrates
the polarzed
polling
loop jwrrrng terminals
and the ID number
programming
switch.
OPERATION:
The ADEMCO
No. 4192
DETECTOR
BASE/TRANSPONDER
communi-
cates
with the control
by a stngle
multiplex
communrcation
crrcutt
(the pol-
ling loop). Security
is maintained
by the control
which
polls each trans-
ponder
on the loop and each transponder
responds
wtth the status
of Its
protection
point. The base/transponder
uses any one of three
rnterchange-
able detector
heads
to detect
combustton.
NOTE:
The detector
head LED is not used
and will not function
when
used In contunction
with the No. 4192.
INSTALLATION:
WHERE
TO INSTALL
For information
regarding
findtng
a suitable
location
for the detector
head
and its base/transponder,
refer to the BRK manual
156-210,
Appltcatron
Manual
for System
Combustton
Detectors
(Available
at no charge
from
BRK Electrontcs,
System
Sensor
Dtvisron,
780 McClure
Road, Aurora,
IL
60504-2495).
PREPARING
THE
No. 4192
Before
installing
the No. 4192. it must be assigned
an identification
number
by arranging
the DIP switches
on the base. Assign
the number
(allocated
in the control's
system
programming
worksheet)
accordtng
to the followtng
chart
.-
1
2345678
pm
OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF
1) OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF. OFF OFF
OFF OFF OF: OFF
OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF ON
OFF OFF OFF ON
OFF OFF
-
II
FF
OFF
OFF
OFF
OFF
OFF
"0:
:I
%
%
OFF
OFF
OFF
ON
ON
OFF
OFF
i%
i%
OFF
OFF
ml
OFF ON
= 1
ON
OFF = 2
ON
ON
= 3
OFF OFF = 4
OFF ON
= 5
g;
:'N':;
OFF OFF = 6
OFF ON
= 9
ON
OFF = 10
ON
ON
= 11
OFF OFF = 12
OFF ON
= 13
ON
OFF=14
ON
ON
= 15
OFF OFF = 16
OFF ON
= 17
OFF = 16
ON
= 1S
g'N' : ;y
OFF = 22
:F"F : ;;
ON
= 25
OFF OFF OFF ON
ON
OFF ON
OFF = 26
OFF OFF OFF ON
ON
OFF ON
ON
= 27
OFF OFF OFF ON
ON
ON
OFF OFF = 26
OFF OFF OFF ON
ON
ON
OFF ON
= 29
OFF OFF OFF ON
ON
ON
ON
OFF = 30
OFF OFF OFF ON
ON
ON
ON
ON
= 31
OFF OFF ON
OFF OFF OFF OFF OFF = 32
OFF OFF ON
OFF OFF OFF OFF ON
= 33
OFF OFF ON
OFF OFF OFF ON
OFF = 34
OFF OFF ON
OFF OFF OFF ON
ON
= 35
OFF OFF ON
OFF OFF ON
OFF OFF = 36
OFF OFF ON
OFF OFF ON
OFF ON
= 37
Diagram
1. TERMINALS
AND ID SWITCH
NOTE:
Two wires
may be used under
the same clamping
plate. but the
wire run must be broken
at the termtnal
to matntarn
electrical
supervision.
CORRECT
INCORRECT
INCORRECT
INSTALLATION
Diagram
2. CORRECT
WIRING
TECHNIQUE
When
wiring
the polling
loop, observe
the following
gauge/length
restrictions:
GAUGE
LENGTH
(ft)'
;i
. . . . . . . . . . . . . . . . . . . . . . 650
(200m)
. . . . . . . . . . . . . . . . . . . .950
(290m)
18 ::.
. . . . . . . . . . . . . . . . . . .1500
(460m)
16 . . . . . . . . . . . . . . . . . . . . . .2400
(730m)
'If multiple
wire runs are extended
from the control,
the maximum
total
length
of wire that can be connected
to the polling
loop is 4,000
feet
(1220m).
independent
of wire gauge.
If shrelded
wtre is used, the maxi-
mum
lengths
in the table are not affected
except
for 16 gauge
wire and
the maximum
total length
of wtre that can be connected
to the polling
loop. Those
two numbers
are now 2000 feet (61 Om). See typical
wiring
diagram
3 and also see typical
mounting
diagrams
4. 5 and 6.
Note that SMOKE
DETECTOR
BASE/TRANSPONDER
can and should
be
installed
on the same
polling
loop as burglary
transponders.
---.-
..___
-.-..-.
~_._.~
~..