ADEMCO 5890 Kurulum Talimatları

Aksesuarlar ADEMCO 5890 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. ADEMCO 5890 4 sayfaları. Passive infrared motion detector/transmitter

Sayfayı Yazdır

N5987V2 5/98

No. 5890

PASSIVE INFRARED MOTION

DETECTOR/TRANSMITTER

INSTALLATION

INSTRUCTIONS

For use with QED control panels ONLY!

GENERAL INFORMATION

The

5890

Passive

Infrared

Detector/Transmitter is a battery-operated

wireless device intended for use as part of a

QED 5800 series wireless alarm system.

Designed for use in commercial and residential

installations, the 5890 is a wall-mounted unit

with a standard lens that provides wide-angle

protection up to a range of 40 feet (12m). For

best coverage, mount the detector so that the

likely direction of intruder motion is a cross the

pattern.

Two optional interchangeable lenses are

available for this detector – the 199PA Pet Alley

lens, and the 199LR Long Range lens (see

PROTECTION PATTERNS FOR OPTIONAL

LENSES on last page).

This document provides installation instructions

for the 5890, but the installer must be familiar

with the Installation Instructions for the QED

5800 Wireless Alarm System with which the

5890 is intended to be used.

FEATURES

•

Wireless operation for fast installation.

•

Dual element pyro-electric sensor provides

positive protection while minimizing false

alarms.

•

Alternate polarity pulse count option offers

greater stability in adverse environments.

•

Provision to turn LED on while walk testing

(LED is turned off after testing).

•

Tampered cover – unit transmits message if

cover is removed.

•

Wall or corner mounting options.

•

Optional Pet Alley and Long Range lenses

available.

SYSTEM DESCRIPTION

Optical System: Uses efficiently designed

Fresnel lenses.

Radio Transmitter: The built-in transmitter

serves only as the communication link to the

alarm system's Receiver/Control, and can send

alarm, tamper, supervisory, and battery status

m e s s a g e s

t o

t h e

s y s t e m ' s

receiver/control. The transmitter is not used for

detection purposes. Each detector has a unique

ID code permanently assigned at the factory.

This ID needs to be "enrolled" by the QED

control system at the time of installation. This

allows each detector used in the system to be

uniquely identified. The QED control must be

programmed to "enroll" the 5890 as an "RF"

type unit (i.e., supervised RF).

To conserve battery life during normal

operation, no more than one transmission

sequence will occur within a 3-minute period.

There is no such time restriction in "test" mode.

Alternate Polarity Pulse Count: Two jumper-

selectable detection response modes are

provided: Instant response (Pulse Count OFF)

and Alternate Polarity Pulse Count (Pulse

Count ON). With Pulse Count OFF, any

detected change in infrared energy will trigger

an immediate alarm signal. This mode is

recommended when the detector is used to

monitor a narrow hallway where coverage is

provided by only a single zone.

Use the Pulse Count ON mode when the

detector is installed in areas where periodic

changes in infrared energy levels are normal

(for example, where forced air heating ducts are

present). In this mode, it requires at least two

detected changes in infrared energy within a

short period before an alarm will be triggered.

Important Note: If the detector is to be used in

the Pulse Count mode, be sure to walk test the

unit in this mode.

SPECIFICATIONS

Coverage:

Standard Lens

Motion

199LR Lens :

199PA Lens :

Pulse Count:

Installer-selectable On/Off link.

Detectable

Walk Rate:

0.5 – 5ft/sec (0.15 – 1.5m/sec).

Mtg. Height:

7ft nominal (2.1m), but may be

mounted at other heights (see

Table 1).

Walk Test

Indicator:

Red LED with Test/Normal

(disable) link.

Batteries:

Two 3-volt Lithium batteries.

Use only Ademco No. 466,

Duracell DL123A, Panasonic

CR123A, Sanyo CR123A, or

Varta CR123A.

0perating

Temperature: 32°F – 122°F (0°C – 50°C)

Operating

Humidity:

Up to 95% RH (max.), non-

condensing.

Dimensions:

2-11/16"W x 5"H x 1-7/8"D

(68mm x 127mm x 48mm).

Q E D

Standard Wide Angle Protection Pattern

BATTERY INSTALLATION

1. Remove front cover by inserting a large

screwdriver blade (or small coin) in groove

between cover and base at the location

shown in Figure 2; rotate blade to override

snap fit, then lift cover off.

40 ft x 56 ft (12 m x 17 m).

18 zones (9 long, 5 inter-

mediate, 4 short range).

60 ft x 6 ft (18m x 1.8m).

5 zones (1 long, 2 inter

mediate, 2 short range).

40 ft x 60 ft (12m x 18m)

12 zones.

Figure 1.

2. Observing correct polarity, install the two

Lithium batteries (supplied) into the battery

holders, as shown in Figure. 5. Make sure

the batteries are firmly seated.

3. Replace the cover (snap fit).

Battery Caution:

Risk of fire, explosion and burns. Do not recharge,

disassemble, heat above 100°C, or incinerate.

Dispose of used batteries promptly. Keep away

from children.

Programming Note: If the detector's ID has

not been programmed into the system (i.e.,

this is an initial detector installation), refer to

the PROGRAMMING section below and

perform the ID "enrolling" procedure before

mounting or testing the detector.

PROGRAMMING

The QED control system must "enroll" the

detector's ID during installation of the system.

The QED control should be programmed to

enroll the 5890 as an "RF" type unit (i.e.,

supervised RF).

To program the detector, place the LED jumper

in the TEST position (see Fig. 5), the Pulse

Count jumper in the OFF position, batteries

installed, and cover on. Temporarily cover the

lens (a cloth will do) to prevent any activation by

the detector.

When prompted for the device's serial number,

you may either manually enter it or transmit

from the unit (remove the cloth cover and

motion your hand over the lens to activate the

detector, press the tamper switch, etc.). Refer

to the QED control panel installation

instructions for programming details.

Return LED jumper to the NORMAL position

after it is enrolled in the control.

INSTALLATION HINTS

Do not install where the detector is exposed

to direct sunlight or directly above strong

sources of heat.

• Make sure the detection area does not have

obstructions (curtains, screens, large pieces

of furniture, plants, etc.) which may block the

pattern of coverage.

• Avoid locating a unit in areas which contain

objects likely to produce a rapid change in

temperature, such as central heating,

radiators or ducts (or heaters of any kind), air

conditioners, open flame, etc.

• Do not mount on an unstable surface.

INSTALLATION

Radio Transmission Path Check

Verify that a strong transmission path between

the 5890 and the system's Receiver/Control

exists before permanently mounting the

detector. Do this by performing the Walk Test

(described later) with the detector temporarily

mounted in its proposed location. The 5890 will

transmit when sensing motion (waving arm or

walking into area). Sometimes, moving the

detector only a few inches means the difference

between a strong and weak transmission path.

Experiment until you are satisfied that the

location provides the strongest transmission

path, while still being practical for the protection

pattern desired. This test also verifies that the

detector has been correctly programmed into

the system.

Normal Mounting

Mount the unit to a firm vertical surface (flat on

wall or in corner).

1. Remove front cover.

2. Temporarily loosen (do not remove) the

screw holding the PC board in the detector

base (see Fig. 5 for location of this screw).