Dynamite Prophet P1 Mini Kullanım Kılavuzu - Sayfa 2
Akü Şarj Cihazı Dynamite Prophet P1 Mini için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Dynamite Prophet P1 Mini 2 sayfaları. Ac battery charger
Sayfayı Yazdır
CHARGE
Li** CHARGE
STORAGE
CHARGE
14.8V (4S)
2.0A
14.8V (4S)
NI-MH/NI-CD CHARGING IS SHOWN AS NI-** . FOLLOW THESE
BATT/PROGRAM
14.8V (4S)
14.8V (4S)
BATT/PROGRAM
FAST CHG
INSTRUCTIONS FOR BOTH NI-MH AND NI-CD CHARGING.
Li** FAST CHG
DISCHARGE
FAST CHG
14.8V (4S)
WARNING: Never charge lithium batteries in Ni-MH, Ni-CD, or Pb mode.
GRAM
2.0A
14.8V (4S)
BATT/PROGRAM
14.8V (4S)
14.8V (4S)
i** BATT
NI** (NI-MH/NI-CD) CHARGING
STORAGE
Li** STORAGE
Ni** BATT
1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the
STORAGE
14.8V (4S)
2.0A
14.8V (4S)
BATT/PROGRAM
positive and negative connectors match, red to red (positive to positive) and black to black
BATT/PROGRAM
BATT/PROGRAM
(negative to negative).
14.8V (4S)
Ni** BATT
Li** BATT
DISCHARGE
Li** DISCHARGE
2. Connect the battery connector to the battery adapter cable.
Ni** BATT
BATT/PROGRAM
3. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
DISCHARGE
14.8V (4S)
1.0A
14.8V (4S)
Ni** BATT
BATT/PROGRAM
scroll through the main menu screens until you reach Program Select=Ni-MH or Ni-Cd.
Li** CHARGE
14.8V (4S)
4. Press the ENTER / Start button.
Ni** BATT
CHARGE
2.0A
14.8V (4S)
BATT/PROGRAM
NT
2.0A
Ni** BATT
Li** FAST CHG
Auto CHARGE
GRAM
2.0A
14.8V (4S)
5. Press the DEC or INC Button until Ni-MH/Ni-Cd CHARGE appears.
NT
3.0A
i** BATT
CHARGE
Ni** CHARGE
Li** STORAGE
CHARGE
DISCHARGE
NT
2.0A
CURRENT
Li** CHARGE
2.0A
14.8V (4S)
BATT/PROGRAM
CUT: 3.2V
NT
2.0A
BATT/PROGRAM
2.0A
14.8V (4S)
Auto CHARGE
Ni** Auto CHARGE
Li** DISCHARGE
6. Press the ENTER / Start Button to edit the parameter.
RE-PEAK
NT
3.0A
Auto CHARGE
CURRENT
Li** FAST CHG
GRAM
1.0A
14.8V (4S)
7. Once the parameters are at the desired settings, press and hold the ENTER / Start button for 3
BATT/PROGRAM
1
seconds.
NT
3.0A
i** BATT
2.0A
14.8V (4S)
DISCHARGE
8. The charger will check the battery and charger settings and charging will begin.
Pb BATT
Ni** DISCHARGE
Li** CHARGE
9. Press the DEC or INC Button to see the rest of the Discharging information.
CUT: 3.2V
CYCLE
DISCHARGE
1.0A
CUT: 3.2V
Li** STORAGE
BATT/PROGRAM
2.0A
14.8V (4S)
BATT/PROGRAM
10. Press Batt / PROG Stop at any time to stop discharging.
BATT/PROGRAM
CHG
1
CUT: 3.2V
Pb BATT
11. When charging is complete, the charger will sound a series of beeps.
Ni** BATT
2.0A
14.8V (4S)
RE-PEAK
Pb BATT
Ni** RE-PEAK
Li** FAST CHG
BATT/PROGRAM
12. Disconnect the battery from the charger when the charge is complete.
Li** CHARGE
1
RE-PEAK
Li** DISCHARGE
Pb BATT
BATT/PROGRAM
2.0A
14.8V (4S)
2.0A
14.8V (4S)
Ni** CHARGE
BATT/PROGRAM
1
Li** CHARGE
1.0A
14.8V (4S)
Pb BATT
NI** (NI-MH/NI-CD) DISCHARGING
CYCLE
Li** STORAGE
Ni** CYCLE
CURRENT
BATT/PROGRAM
2.0A
14.8V (4S)
Li** FAST CHG
Li** CHARGE
CHG
1
1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the
CYCLE
CHG>DCHG
Pb BATT
2.0A
14.8V (4S)
positive and negative connectors match, red to red (positive to positive) and black to black
BATT/PROGRAM
Ni** Auto CHARGE
2.0A
14.8V (4S)
2.0A
14.8V (4S)
Li** FAST CHG
CHG
1
(negative to negative).
ARGE
i** BATT
BATT METER
Li** DISCHARGE
CURRENT
GRAM
2. Connect the battery connector to the battery adapter cable.
Li** CHARGE
2.0A
12.0V (6P)
14.8V (4S)
Li** STORAGE
Li** FAST CHG
3. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
i** BATT
BATT/PROGRAM
1.0A
14.8V (4S)
2.0A
14.8V (4S)
BATT/PROGRAM
2.0A
14.8V (4S)
Ni** DISCHARGE
2.0A
14.8V (4S)
Li** STORAGE
BATT METER
SCHARGE
BATT/PROGRAM
BATT METER
Ni** CHARGE
1.0A
CUT: 3.2V
BATT/PROGRAM
Li** FAST CHG
2.0A
12.0V (6P)
14.8V (4S)
Li** DISCHARGE
BATT RESISTANCE
Li** STORAGE
BATT/PROGRAM
ARGE
CURRENT
2.0A
BATT METER
BATT/PROGRAM
Li** CHARGE
Pb CHARGE
2.0A
14.8V (4S)
1.0A
14.8V (4S)
Ni** RE-PEAK
Li** DISCHARGE
2.0A
14.8V (4S)
scroll through the main menu screens until you reach Program Select=Ni-MH/Ni-Cd.
12.0V (6P)
BATT METER
ARGE
BATT/PROGRAM
2.0A
12.0V (6P)
2.0A
14.8V (4S)
4. Press the ENTER / Start button.
GRAM
Ni** Auto CHARGE
BATT/PROGRAM
Li** STORAGE
1.0A
14.8V (4S)
12.0V (6P)
BATT RESISTANCE
Li** DISCHARGE
5. Press the DEC or INC Button until Ni-MH/Ni-Cd DISCHARGE appears.
Pb BATT
SCHARGE
CURRENT
3.0A
BATT METER
Li** FAST CHG
6. Press the ENTER / Start Button to edit the parameter.
Pb DISCHARGE
2.0A
14.8V (4S)
Ni** CHARGE
Ni** CYCLE
1.0A
BATT/PROGRAM
14.8V (4S)
0.00 0.00 V
12.0V (6P)
Li** CHARGE
7. Once the parameters are at the desired settings, press and hold the ENTER / Start button for 3
SCHARGE
BATT/PROGRAM
1.0A
12.0V (6P)
2.0A
14.8V (4S)
BATT RESISTANCE
seconds.
CHG>DCHG
CURRENT
Ni** DISCHARGE
BATT/PROGRAM
2.0A
Li** DISCHARGE
2.0A
12.0V (6P)
14.8V (4S)
BATT RESISTANCE
V
BATT/PROGRAM
8. The charger will check the battery and charger settings and charging will begin.
1.0A
CUT: 3.2V
Pb BATT
Li** STORAGE
1.0A
14.8V (4S)
9. Press the DEC or INC Button to see the rest of the Discharging information.
Ni** Auto CHARGE
BATT RESISTANCE
BATT/PROGRAM
IN:
Li** FAST CHG
0.00V
Ni** CHARGE
10. Press Batt / PROG Stop at any time to stop discharging.
2.0A
14.8V (4S)
Ni** RE-PEAK
CURRENT
3.0A
BATT RESISTANCE
11. When discharging is complete, the charger will sound a series of beeps.
CURRENT
0
L:0.00V
2.0A
14.8V (4S)
Ni** CHARGE
BATT/PROGRAM
BATT/PROGRAM
0.00 0.00 V
1
12. Disconnect the battery from the charger when the discharge is complete.
Li** DISCHARGE
0.00 0.00 0.00 V
Ni** DISCHARGE
BATT RESISTANCE
CURRENT
2.0A
Ni** Auto CHARGE
Li** STORAGE
0.00 0.00 V
V
Ni** CHARGE
1.0A
14.8V (4S)
0.00
GRAM
1.0A
Ni** CYCLE
RY CHECK
CUT: 3.2V
Pb CHARGE
CURRENT
NI** (NI-MH/NI-CD) CYCLE CHARGING
2.0A
14.8V (4S)
V
CURRENT
2.0A
Ni** Auto CHARGE
ATT METER
IN:
CHG>DCHG
0.00V
1
.............
2.0A
MAIN:
12.0V (6P)
0.00V
i** BATT
1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the
Ni** RE-PEAK
GRAM
Ni** CHARGE
CURRENT
3.0A
Li** DISCHARGE
positive and negative connectors match, red to red (positive to positive) and black to black
Ni** DISCHARGE
IN:
0
L:0.00V
0.00V
Ni** Auto CHARGE
H:0.00
L:0.00V
Pb BATT
(negative to negative).
BATT/PROGRAM
1
IN:
0.00V
CURRENT
2.0A
Pb DISCHARGE
1.0A
CUT: 3.2V
0
1.0A
L:0.00V
14.8V (4S)
CURRENT
3.0A
2. Connect the battery connector to the battery adapter cable.
Ni** DISCHARGE
BATT METER
0
L:0.00V
1.0A
12.0V (6P)
3. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
BATT/PROGRAM
RY CHECK
Ni** CYCLE
Ni** Auto CHARGE
1.0A
CUT: 3.2V
BATTERY CHECK
Ni** RE-PEAK
scroll through the main menu screens until you reach Program Select=Ni-MH/Ni-Cd.
Ni** DISCHARGE
BATT RESISTANCE
CHG>DCHG
1
Ni** CHARGE
RY CHECK
.............
4. Press the ENTER / Start button.
CURRENT
3.0A
...................
1.0A
GRAM
CUT: 3.2V
Ni** RE-PEAK
5. Press the DEC or INC button until Ni-MH/Ni-Cd CYCLE appears.
CURRENT
.............
2.0A
Pb CHARGE
SISTANCE
IN:
0.00V
1
Ni** DISCHARGE
MAIN:
0.00V
Ni** CYCLE
Ni** RE-PEAK
2.0A
12.0V (6P)
Ni** Auto CHARGE
IN:
0
L:0.00V
0.00V
1.0A
CUT: 3.2V
0.00 0.00 0.00 V
CHG>DCHG
H:0.00
L:0.00V
1
BATT/PROGRAM
Ni** CYCLE
Ni** CHARGE
CURRENT
3.0A
0
L:0.00V
Pb DISCHARGE
0.00
GRAM
BATT RESISTANCE
Ni** RE-PEAK
CHG>DCHG
1
CURRENT
2.0A
Ni** CYCLE
1.0A
12.0V (6P)
ATT METER
6. Press the ENTER / Start button to select the cycle direction. The direction may be changed
Ni** DISCHARGE
1
MAIN:
0.00V
Pb CHARGE
with the lettering is flashing, press the DEC or INC button to change between CHG>DCHG or
CHG>DCHG
1
Ni** Auto CHARGE
DCHG>CHG.
1.0A
CUT: 3.2V
2.0A
12.0V (6P)
H:0.00
L:0.00V
7. Press the ENTER / Start Button to define the number of cycles. When the number flashes number
Ni** CYCLE
CURRENT
3.0A
of cycles can be set with the DEC or INC button. Current settings for charge and discharge rates
Ni** RE-PEAK
CHG>DCHG
1
Pb DISCHARGE
will be applied for Ni** cycling
Pb CHARGE
BATTERY CHECK
Ni** DISCHARGE
8. Once the parameters are set, press and hold the ENTER / Start button for 3 seconds.
1
0.00 0.00 0.00 V
1.0A
12.0V (6P)
2.0A
12.0V (6P)
9. The charger will check the battery and charger settings and charging will begin.
1.0A
CUT: 3.2V
...................
Pb CHARGE
GRAM
0.00
V
10. Press the DEC or INC Button to see the rest of the Cycle information.
Ni** CYCLE
Pb BATT
2.0A
12.0V (6P)
SISTANCE
11. Press Batt / PROG Stop at any time to stop discharging.
Pb DISCHARGE
Pb CHARGE
Ni** RE-PEAK
MAIN:
0.00V
CHG>DCHG
1
MAIN:
0.00V
12. When cycling is complete, the charger will sound a series of beeps.
1.0A
12.0V (6P)
2.0A
12.0V (6P)
1
H:0.00
L:0.00V
Pb DISCHARGE
13. Disconnect the battery from the charger when the cycle is complete.
H:0.00
L:0.00V
0.00 0.00 0.00 V
1.0A
12.0V (6P)
Pb CHARGE
Pb DISCHARGE
Ni** CYCLE
0.00
V
2.0A
12.0V (6P)
1.0A
12.0V (6P)
BATTERY CHECK
CHG>DCHG
1
MAIN:
0.00V
...................
Pb DISCHARGE
During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger's LCD screen, make the recommended responses. If the message continues
0.00 0.00 0.00 V
after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance.
H:0.00
L:0.00V
Pb CHARGE
1.0A
12.0V (6P)
0.00
MAIN:
0.00V
0.00 0.00 0.00 V
2.0A
12.0V (6P)
REVERSE POLARITY
Confirm polarity is correct between the charger and the battery.
ATT METER
H:0.00
L:0.00V
0.00
V
MAIN:
0.00 0.00 0.00 V
BATTERY CHECK
CONNECTION BREAK
The battery connection has been broken
Pb DISCHARGE
H:0.00
L:0.00V
0.00
V
...................
MAIN:
0.00V
Pb CHARGE
1.0A
12.0V (6P)
CONNECT ERROR
The battery connection is incorrect
0.00 0.00 0.00 V
2.0A
H:0.00
12.0V (6P)
L:0.00V
CHECK MAIN PORT
MAIN:
0.00V
MAIN:
0.00V
BATTERY CHECK
0.00
V
H:0.00
L:0.00V
H:0.00
L:0.00V
BALANCE CONNECT
The balance connection is incorrect
Pb DISCHARGE
...................
BATTERY CHECK
ERROR
MAIN:
0.00V
1.0A
12.0V (6P)
SISTANCE
...................
MAIN:
0.00 0.00 0.00 V
BATTERY CHECK
H:0.00
L:0.00V
CELL ERROR
The voltage of one cell in the battery pack is too low
LOW VOLTAGE
H:0.00
L:0.00V
0.00
V
...................
MAIN:
0.00V
BATTERY CHECK
H:0.00
CELL ERROR
L:0.00V
The voltage of one cell in the battery pack is too high
MAIN:
0.00V
MAIN:
0.00V
HIGH VOLTAGE
0.00 0.00 0.00 V
...................
H:0.00
L:0.00V
H:0.00
L:0.00V
CELL ERROR
The voltage of one cell in the battery pack is invalid
0.00
V
MAIN:
0.00V
VOLTAGE-INVALID
BATTERY CHECK
H:0.00
MAIN:
L:0.00V
0.00V
CELL NUMBER
The number of cells the charger is set for does not match the battery
...................
INCORRECT
H:0.00
L:0.00V
MAIN:
INT. TEMP. TOO HI
0.00V
The internal temperature of the charger is too high
BATTERY CHECK
H:0.00
L:0.00V
EXT. TEMP. TOO HI
The external temperature of the battery is too high (the optional temp probe DYN5033 is required to test external temperature)
...................
OVER CHARGE
The charger has stopped charging because it reached the capacity limit set by the user
MAIN:
0.00V
CAPACITY LIMIT
H:0.00
L:0.00V
OVER THE LIMIT
The charger has stopped chargin beause it reached the charge time limit
BATTERY WAS FULL
The battery voltage is higher than the maximum voltage set by the user when the charge is initiated
CONTROL FAIL
Battery pack voltage is lower than 5 volts. The Prophet P1 Mini cannot charge a pack with a voltage less than 5 volts.
© 2018 Horizon Hobby, LLC. Dynamite, Prophet , EC3 and the Horizon Hobby Logo are trademarks or registered trademarks of Horizon Hobby, LLC. All other trademarks, service marks and logos are property of their respective owners.
2.0A
1.0A
14.8V (4S)
Li** DISCHARGE
Ni** CHARGE
BATT/PROGRAM
Ni** Auto CHARGE
Li** FAST CHG
1.0A
14.8V (4S)
SYSTEM SETTING->
CURRENT
BATT/PROGRAM
2.0A
CURRENT
2.0A
All manuals and user guides at all-guides.com
SYSTEM SETTING->
Ni** BATT
Ni** CHARGE
Li** CHARGE
Li** BATT
Ni** CHARGE
Ni** Auto CHARGE
Ni** DISCHARGE
CAUTION: The Pb charge program menus are to be used ONLY for the charging and
Li** STORAGE
CURRENT
2.0A
2.0A
14.8V (4S)
discharging of Pb battery packs. Charging other battery types using the Pb charge
CURRENT
CURRENT
3.0A
2.0A
1.0A
Ni** CHARGE
programs will damage the battery or the charger.
2.0A
Ni** Auto CHARGE
Ni** CHARGE
Li** FAST CHG
CURRENT
2.0A
Ni** Auto CHARGE
Ni** DISCHARGE
Ni** RE-PEAK
PB CHARGING
Li** DISCHARGE
CURRENT
3.0A
CURRENT
2.0A
2.0A
14.8V (4S)
1.0A
CURRENT
CUT: 3.2V
3.0A
Ni** Auto CHARGE
1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the
Ni** CHARGE
1.0A
positive and negative connectors match, red to red (positive to positive) and black to black
Li** STORAGE
Ni** Auto CHARGE
Ni** DISCHARGE
CURRENT
3.0A
CURRENT
(negative to negative).
Ni** RE-PEAK
Ni** DISCHARGE
Ni** CYCLE
2. Connect the battery connector to the battery adapter cable.
1.0A
CUT: 3.2V
CURRENT
3.0A
2.0A
14.8V (4S)
1.0A
CUT: 3.2V
1
CHG>DCHG
Ni** DISCHARGE
Ni** Auto CHARGE
3. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
Ni** RE-PEAK
Li** DISCHARGE
BATT/PROGRAM
1.0A
CUT: 3.2V
Ni** DISCHARGE
CURRENT
Ni** RE-PEAK
Ni** CYCLE
1
1.0A
1.0A
CUT: 3.2V
14.8V (4S)
1
CHG>DCHG
1
Ni** RE-PEAK
Ni** DISCHARGE
Ni** CHARGE
1
Ni** RE-PEAK
Ni** CYCLE
1.0A
CUT: 3.2V
Ni** CYCLE
scroll through the main menu screens until you reach Program Select=Pb BATT.
CURRENT
CHG>DCHG
1
1
CHG>DCHG
1
Ni** CYCLE
Ni** RE-PEAK
Pb CHARGE
Ni** Auto CHARGE
2.0A
CHG>DCHG
1
Ni** CYCLE
2.0A
BATT/PROGRAM
CURRENT
CHG>DCHG
1
Pb BATT
Ni** CHARGE
Ni** CYCLE
SYSTEM SETTING->
Pb CHARGE
Ni** BATT
Pb DISCHARGE
4. Press the ENTER / Start button.
3.0A
Ni** DISCHARGE
BATT/PROGRAM
CURRENT
2.0A
2.0A
CHG>DCHG
12.0V (6P)
1.0A
5. Press the DEC or INC Button until Pb CHARGE appears.
1.0A
6. Press the ENTER / Start Button to edit the parameter.
Pb CHARGE
Ni** Auto CHARGE
Pb CHARGE
7. Once the parameters are at the desired settings, press and hold the ENTER / Start button for 3
Pb DISCHARGE
2.0A
12.0V (6P)
BATT/PROGRAM
seconds.
Ni** RE-PEAK
2.0A
CURRENT
12.0V (6P)
3.0A
1.0A
12.0V (6P)
Pb CHARGE
8. The charger will check the battery and charger settings and charging will begin.
SYSTEM SETTING->
9. Press the DEC or INC Button to see the rest of the charging information.
2.0A
12.0V (6P)
Pb CHARGE
Pb DISCHARGE
Ni** DISCHARGE
Pb DISCHARGE
0.00 0.00 0.00 V
10. Press Batt / PROG Stop at any time to stop discharging.
1.0A
12.0V (6P)
2.0A
12.0V (6P)
1
Ni** CYCLE
1.0A
CUT: 3.2V
11. When charging is complete, the charger will sound a series of beeps.
1.0A
12.0V (6P)
0.00
Pb DISCHARGE
Pb CHARGE
BATT/PROGRAM
12. Disconnect the battery from the charger when the charge is complete.
CHG>DCHG
1.0A
12.0V (6P)
BATT METER
2.0A
12.0V (6P)
Pb DISCHARGE
2.0A
BATT/PROGRAM
BATT RESISTANCE
Ni** RE-PEAK
0.00 0.00 0.00 V
MAIN:
1.0A
12.0V (6P)
1
SYSTEM SETTING->
0.00
V
BATT/PROGRAM
H:0.00
Pb DISCHARGE
PB DISCHARGING
0.00 0.00 0.00 V
1. Connect the banana plugs of the battery adapter cable to the charge port (H,L). Confirm the
SYSTEM SETTING->
1.0A
12.0V (6P)
3.0A
Ni** CYCLE
0.00 0.00 0.00 V
MAIN:
0.00V
positive and negative connectors match, red to red (positive to positive) and black to black
0.00
V
BATTERY CHECK
(negative to negative).
CHG>DCHG
BATT/PROGRAM
0.00
V
H:0.00
L:0.00V
0.00 0.00 0.00 V
2. Connect the battery connector to the battery adapter cable.
...................
SYSTEM SETTING->
Pb CHARGE
MAIN:
0.00V
0.00 0.00 0.00 V
0.00
3. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
V
MAIN:
0.00V
scroll through the main menu screens until you reach Program Select=Pb BATT.
2.0A
BATTERY CHECK
H:0.00
L:0.00V
0.00
V
MAIN:
4. Press the ENTER / Start button.
H:0.00
L:0.00V
MAIN:
0.00 0.00 0.00 V
0.00V
Pb BATT
...................
BATT/PROGRAM
H:0.00
Pb DISCHARGE
MAIN:
0.00V
H:0.00
1
0.00
L:0.00V
SYSTEM SETTING->
BATTERY CHECK
1.0A
BATTERY CHECK
MAIN:
0.00V
H:0.00
L:0.00V
Pb CHARGE
...................
MAIN:
0.00V
...................
BATTERY CHECK
H:0.00
L:0.00V
2.0A
12.0V (6P)
H:0.00
L:0.00V
1
5. Press the DEC or INC Button until Pb DISCHARGE appears.
BATT/PROGRAM
MAIN:
0.00V
BATTERY CHECK
...................
MAIN:
0.00V
6. Press the ENTER / Start Button to edit the parameter.
SYSTEM SETTING->
Pb DISCHARGE
...................
H:0.00
L:0.00V
7. Once the parameters are at the desired settings, press and hold the ENTER / Start button for 3
H:0.00
L:0.00V
MAIN:
0.00V
BATTERY CHECK
0.00 0.00 0.00 V
seconds.
1.0A
12.0V (6P)
2.0A
8. The charger will check the battery and charger settings and discharging will begin.
MAIN:
0.00V
H:0.00
...................
L:0.00V
0.00
9. Press the DEC or INC Button to see the rest of the Discharging information.
H:0.00
L:0.00V
BATT METER
10. Press Batt / PROG Stop at any time to stop discharging.
MAIN:
0.00V
MAIN:
V
11. When discharging is complete, the charger will sound a series of beeps.
3.0A
H:0.00
L:0.00V
12. Disconnect the battery from the charger when the discharge is complete.
H:0.00
0.00 0.00 0.00 V
0.00
BATTERY CHECK
MAIN:
...................
0.00V
H:0.00
L:0.00V
1
MAIN:
H:0.00
BATTERY CHECK
1
...................
V
MAIN:
0.00V
H:0.00
L:0.00V
TROUBLESHOOTING
V
0.00V
0.00V
14.8V (4S)
ON
Ni** RE-PEAK
Saftety Timer
BATT/PROGRAM
ON
Temp Cut-Off
Saftety Timer
3.0A
SYSTEM SETTING->
14.8V (4S)
SYSTEM SETTINGS
On
ON
Ni** CYCLE
Capacity Cut-Off
BATT/PROGRAM
CHG>DCHG
ON
Capacity Cut-Off
Temperature Unit
CUT: 3.2V
SYSTEM SETTING->
14.8V (4S)
ON
Temp Cut-Off
1. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
On
Rest Time
1
Temp Cut-Off
scroll through the main menu screens until you reach BATT/PROGRAM SYSTEM SETTINGS page.
14.8V (4S)
2. Press the ENTER / Start button to enter the system setting menu.
CHG>DCHG
On
2.0A
Temperature Unit
3. Press the DEC or INC button to scroll through the menu.
4. Press the ENTER / Start button to edit the parameter.
Pb CHARGE
NiMH Sensitivity
Temperature Unit
1
5. Press the DEC or INC button to increase or decrease the value.
2.0A
12.0V (6P)
BATT/PROGRAM
D.Peak
6. Press the ENTER / Start button again to save the selection.
3.0A
Rest Time
SYSTEM SETTING->
7. Press the Batt / PROG Stop button to return to the main menu.
Pb BATT
Pb DISCHARGE
NiCd Sensitivity
CHG>DCHG
Rest Time
SAFETY TIMER DEFAULT IS ON, 120MIN
1.0A
12.0V (6P)
D.Peak
CHG>DCHG
Use the Safety Timer menu to set a time limit for charging a battery. When a charge cycle is
NiMH Sensitivity
started, a clock inside the charger will begin recording the elapsed charge time. If the safety
2.0A
timer function has been turned ON, the charger will stop the charging process once this time
Key Beep
D.Peak
NiMH Sensitivity
limit has been reached to avoid damage caused by overcharging the battery. This time value
can be set between 10 and 720 minutes, in 10 minute Increments.
Buzzer
D.Peak
1
12.0V (6P)
NiCd Sensitivity
Saftety Timer
3.0A
0.00 0.00 0.00 V
Bal. Connection
NiCd Sensitivity
D.Peak
ON
0.00
D.Peak
1
12.0V (6P)
Key Beep
Capacity Cut-Off
BATT METER
CUT: 3.2V
CAPACITY CUT-OFF DEFAULT IS ON, 5000MAH
Buzzer
MAIN:
Load Factory Set
Key Beep
Use the Capacity Cut-Off menu to set a capacity limit on when the charger stops charging
ON
a battery. When a charge cycle starts, the charger records the battery capacity. When the
Saftety Timer
H:0.00
Buzzer
capacity cutoff function is set at ON, the charger will stop charging at the capacity limit to
Bal. Connection
prevent battery damage. Capacity can be adjusted between 10 and 50,000mAh in 100mAh
ON
Temp Cut-Off
1
Increments.
Version
Bal. Connection
On
BATTERY CHECK
HW:1.00
Capacity Cut-Off
BATT/PROGRAM
V
Load Factory Set
...................
Temperature Unit
ON
1
SYSTEM SETTING->
Load Factory Set
Saftety Timer
0.00V
MAIN:
Temp Cut-Off
1
ON
TEMP. CUT-OFF DEFAULT IS 50C/122F
Version
Saftety Timer
L:0.00V
H:0.00
The charger can be used in conjunction with a battery mounted temperature sensor (sold
On
Rest Time
HW:1.00
BATT/PROGRAM
separately, DYN5033) connected to the Temperature Sensor Port to monitor the temperature
Version
ON
Capacity Cut-Off
CHG>DCHG
of the battery during the charging process. If the battery temperature reaches the cut-off
BATT MEMORY
HW:1.00
limit, the charger will stop the charging process. Temperature values can be adjusted
Temperature Unit
Saftety Timer
ON
1
Capacity Cut-Off
between 20–80° C (68–176° F).
NiMH Sensitivity
ON
ON
Temp Cut-Off
D.Peak
12.0V (6P)
[ BATT MEMORY X ]
Rest Time
0.00V
On
Capacity Cut-Off
BATT/PROGRAM
Temp Cut-Off
NiCd Sensitivity
CHG>DCHG
Saftety Timer
ENTER SET->
ON
L:0.00V
BATT MEMORY
On
BATT/PROGRAM
V
Temperature Unit
The following screen sets the charger for Celcius or Farenheit.
D.Peak
ON
12.0V (6P)
NiMH Sensitivity
BATT MEMORY
Temp Cut-Off
Temperature Unit
Key Beep
D.Peak
Capacity Cut-Off
On
[ BATT MEMORY X ]
Buzzer
Rest Time
Saftety Timer
ON
NiCd Sensitivity
[ BATT MEMORY X ]
ENTER SET->
Temperature Unit
CHG>DCHG
ON
Rest Time
REST TIME FOR CYCLE– DEFAULT IS 10 MINUTES
Bal. Connection
D.Peak
Temp Cut-Off
ENTER SET->
Sets the delay during a Charge/Discharge cycle, after the charge completes, before the
CHG>DCHG
NiMH Sensitivity
discharge begins.
Capacity Cut-Off
On
V
Key Beep
D.Peak
Rest Time
ON
NiMH Sensitivity
Buzzer
Load Factory Set
Temperature Unit
CHG>DCHG
0.00V
D.Peak
NiCd Sensitivity
Temp Cut-Off
Bal. Connection
L:0.00V
NiMH Sensitivity
D.Peak
On
NiCd Sensitivity
NI-MH SENSITIVITY D. PEAK – DEFAULT
Version
D.Peak
Rest Time
The D.Peak (Delta Peak) value is adjustable between 3mV/Cell and 15mV/Cell. 8mV/Cell
D.Peak
V
Key Beep
HW:1.00
is a good starting point for Ni-MH batteries. If the Delta Peak value is too high, you risk
Temperature Unit
CHG>DCHG
overcharging the battery; if the value is too low, charging will stop before the battery reaches
Load Factory Set
Buzzer
NiCd Sensitivity
full capacity.
Key Beep
NiMH Sensitivity
D.Peak
Buzzer
Bal. Connection
Rest Time
D.Peak
0.00V
Version
Key Beep
CHG>DCHG
Bal. Connection
L:0.00V
HW:1.00
BATT/PROGRAM
NiCd Sensitivity
Buzzer
NI-CD SENSITIVITY D. PEAK – DEFAULT
Load Factory Set
NiMH Sensitivity
The D.Peak (Delta Peak) value is adjustable between 3mV/Cell and 15mV/Cell. 10mV/
D.Peak
Cell is a good starting point for Ni-Cd batteries. If the Delta Peak value is too high, you risk
Bal. Connection
D.Peak
overcharging the battery; if the value is too low, charging will stop before the battery reaches
Load Factory Set
full capacity.
Key Beep
Version
NiCd Sensitivity
[ BATT MEMORY X ]
Buzzer
BATT/PROGRAM
HW:1.00
Load Factory Set
D.Peak
Version
Bal. Connection
HW:1.00
Key Beep
Version
Buzzer
[ BATT MEMORY X ]
HW:1.00
Load Factory Set
DYNAMITE P1 MINI
BATT/PROGRAM
Bal. Connection
DYNC3015
BATT/PROGRAM
Version
What this Warranty Covers - Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that
Load Factory Set
HW:1.00
the product purchased (the "Product") will be free from defects in materials and workmanship for
DYNAMITE P1 MINI
BATT/PROGRAM
[ BATT MEMORY X ]
a period of 5 years from the date of purchase.
What is Not Covered - This warranty is not transferable and does not cover (i) cosmetic damage,
READ THE MANUAL?
DYNC3015
DYNAMITE P1 MINI
(ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to
[ BATT MEMORY X ]
Version
improper use, installation, operation or maintenance, (iii) modification of or to any part of the
PRESS>TO CONFIRM
DYNC3015
Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center,
HW:1.00
(v) Product not purchased from an authorized Horizon dealer, (vi) Product not compliant with
BATT/PROGRAM
applicable technical regulations, or (vii) use that violates any applicable laws, rules, or regulations.
[ BATT MEMORY X ]
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING,
READ THE MANUAL?
WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE
PRESS>TO CONFIRM
READ THE MANUAL?
HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE
BATT/PROGRAM
PURCHASER'S INTENDED USE.
[ BATT MEMORY X ]
PRESS>TO CONFIRM
Purchaser's Remedy - Horizon's sole obligation and purchaser's sole and exclusive remedy shall
be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by
Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a
warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of
purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY.
[ BATT MEMORY X ]
Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN
ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,
NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon
exceed the individual price of the Product on which liability is asserted. As Horizon has no control over
use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any
resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability.
If you as the purchaser or user are not prepared to accept the liability associated with the use of the
Product, purchaser is advised to return the Product immediately in new and unused condition to the
DYNAMITE P1 MINI
place of purchase.
Law - These terms are governed by Illinois law (without regard to conflict of law principals). This
warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services - Your local hobby store and/or place of purchase cannot provide
warranty support or service. Once assembly, setup or use of the Product has been started, you must
contact your local distributor or Horizon directly. This will enable Horizon to better answer your
DYNAMITE P1 MINI
questions and service you in the event that you may need any assistance. For questions or assistance,
READ THE MANUAL?
PRESS>TO CONFIRM
Country of Purchase
DYNAMITE P1 MINI
READ THE MANUAL?
United States of America
DYNAMITE P1 MINI
PRESS>TO CONFIRM
DYNAMITE P1 MINI
EU
READ THE MANUAL?
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
PRESS>TO CONFIRM
READ THE MANUAL?
against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
DYNAMITE P1 MINI
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
PRESS>TO CONFIRM
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
READ THE MANUAL?
• Increase the separation between the equipment and receiver.
PRESS>TO CONFIRM
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
DYNAMITE P1 MINI
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
READ THE MANUAL?
PRESS>TO CONFIRM
READ THE MANUAL?
PRESS>TO CONFIRM
5000mAh
SYSTEM SETTING->
Saftety Timer
1
120Min
ON
120Min
KEY BEEP (DEFAULT ON) / BUZZER (DEFAULT ON)
50C 122F
120Min
Use the Key Beep/Buzzer menu to set the key beep and charger alarm buzzer at ON or OFF
Capacity Cut-Off
as needed. We recommend that you leave the alarm ON to alert you when charging is
1
complete or if there is cause for alarm during charging.
5000mAh
ON
5000mAh
Celcius
5000mAh
Temp Cut-Off
50C 122F
On
50C 122F
BALANCE CONNECTION (DEFAULT ON)
10Min
50C 122F
UWhen the Balance connection is on the charger will require a balance connection for Li-XX
Temperature Unit
batteries and will confim the batteries are within safe limits or the charger will not start the
Celcius
charge process.
Celcius
Saftety Timer
4mV
Celcius
Rest Time
ON
120Min
10Min
CHG>DCHG
10Min
Capacity Cut-Off
LOAD FACTORY SETTINS PRESS ENTER > 2S
4mV
10Min
Press the ENTER / Start button for more than 2 seconds to reset all charger values to the
NiMH Sensitivity
ON
5000mAh
default values.
4mV
ON
D.Peak
4mV
ON
Temp Cut-Off
4mV
NiCd Sensitivity
On
50C 122F
4mV
D.Peak
4mV
120Min
BATTERY MEMORY
ON
Temperature Unit
V
4mV
ON
The charger can store up to 10 settings for specific batteries. The following images show
Key Beep
Celcius
programming a Li** battery, options will vary with Ni** and Pb battery types.
0.00V
ON
ON
Buzzer
5000mAh
Enter
L:0.00V
ON
Rest Time
Bal. Connection
CHG>DCHG
10Min
120Min
ON
50C 122F
1. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to
NiMH Sensitivity
SW:1.03
ON
scroll through the main menu screens until you reach BATT/PROGRAM BATT MEMORY.
Saftety Timer
2. Press the ENTER / Start button to enter the Battery Memory settings
D.Peak
Load Factory Set
4mV
5000mAh
ON
120Min
3. Press the DEC or INC button to select the battery memory (1-10) you wish to configure.
Enter
Enter
Celcius
0.00V
NiCd Sensitivity
Enter
120Min
Capacity Cut-Off
L:0.00V
Version
50C 122F
D.Peak
4mV
ON
5000mAh
SW:1.03
120Min
HW:1.00
SW:1.03
10Min
4. Press the ENTER / Start button to go to the first page of settings for the selected battery memory.
Key Beep
SW:1.03
5000mAh
Temp Cut-Off
5. Press the ENTER / Start button to edit the parameter.
Buzzer
Celcius
120Min
On
50C 122F
6. Press the DEC or INC button to increase or decrease the value of each page. When the value is
5000mAh
4mV
flashing it can be adjusted with the increase or decrease buttons.
Bal. Connection
50C 122F
Temperature Unit
BATT/PROGRAM
10Min
5000mAh
Celcius
50C 122F
BATT MEMORY
4mV
120Min
Load Factory Set
Celcius
7. Press the ENTER / Start button again to save the selection. When all the values on the page are
Rest Time
solid and do not flash, pressing the increase or decrease buttons will move to the next value in
Enter
4mV
ON
50C 122F
CHG>DCHG
10Min
Celcius
the battery memory.
ON
[ BATT MEMORY X ]
5000mAh
8. Complete the menu options for the battery memory, and press the ENTER / Start on the Save
Version
Program page to save the battery memory. The changes to the battery memory will not be saved if
10Min
NiMH Sensitivity
120Min
ENTER SET->
HW:1.00
SW:1.03
this option is not selected.
4mV
Celcius
D.Peak
4mV
10Min
ON
50C 122F
ON
4mV
NiCd Sensitivity
5000mAh
ON
10Min
D.Peak
4mV
4mV
Enter
Celcius
BATT/PROGRAM
4mV
Key Beep
50C 122F
ON
BATT MEMORY
4mV
Buzzer
4mV
ON
SW:1.03
10Min
ON
Bal. Connection
Celcius
ON
Enter
[ BATT MEMORY X ]
4mV
ON
ENTER SET->
4mV
ON
ON
Load Factory Set
10Min
SW:1.03
ON
Enter
ON
BATT MEMORY
4mV
Enter
Version
4mV
ON
ON
HW:1.00
SW:1.03
Enter
9. Press the Batt / PROG Stop button to return to the main menu.
ON
SW:1.03
4mV
ENTER SET->
BATT MEMORY
Enter
SW:1.03
ON
ON
BATT/PROGRAM
ON
10. To select a battery memory, access the BATT/PROGRAM BATT MEMORY screen, select the
SW:1.03
BATT MEMORY
memory number desired and press the ENTER / Start button to start the charge.
11. Re-load the factory settings in the SYSTEM SETTINGS menu to reset the battery memory slots.
Enter
ENTER SET->
BATT MEMORY
ON
LIMITED WARRANTY
LIMITED WARRANTY
BATT MEMORY
[ BATT MEMORY X ]
please visit our website at horizonhobby.com, submit an inquiry to [email protected] or
call the toll-free telephone number referenced in the Warranty and Service Contact Information section
SW:1.03
ENTER SET->
to speak with a Product Support representative.
Enter
DYNAMITE P1 MINI
Inspection or Services - If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online Service Request submission
BATT MEMORY
ENTER SET->
DYNC3015
process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)
number. Pack the Product securely using a shipping carton. Please note that original boxes may be
ENTER SET->
included, but are not designed to withstand the rigors of shipping without additional protection.
SW:1.03
Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is
not responsible for merchandise until it arrives and is accepted at our facility. An Online Service
Request is available at http://www.horizonhobby.com/content/service-center_render-service-
BATT MEMORY
center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA
ENTER SET->
number along with instructions for submitting your product for service. When calling Horizon, you
READ THE MANUAL?
will be asked to provide your complete name, street address, email address and phone number
where you can be reached during business hours. When sending product into Horizon, please
PRESS>TO CONFIRM
include your RMA number, a list of the included items, and a brief summary of the problem. A
copy of your original sales receipt must be included for warranty consideration. Be sure your
BATT MEMORY
name, address, and RMA number are clearly written on the outside of the shipping carton.
ENTER SET->
Provided warranty conditions have been met, your Product will be serviced or replaced free of charge.
Service or replacement decisions are at the sole discretion of Horizon.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery,
DYNAMITE P1 MINI
please contact the appropriate Horizon Product Support office. Warranty Requirements - For
Warranty consideration, you must include your original sales receipt verifying the proof-of-
DYNC3015
purchase date.
ENTER SET->
Non-Warranty Service -
Should your service not be covered by warranty, service will be completed and payment will be
required without notification or estimate of the expense unless the expense exceeds 50% of the
retail purchase cost. By submitting the item for service you are agreeing to payment of the service
without notification. Service estimates are available upon request. You must include this request
with your item submitted for service. Non-warranty service estimates will be billed a minimum
READ THE MANUAL?
of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders
PRESS>TO CONFIRM
and cashier's checks, as well as Visa, MasterCard, American Express, and Discover cards. By
submitting any item to Horizon for service, you are agreeing to Horizon's Terms and Conditions
DYNC3015
found on our website http://www.horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and
ownership. If received, a non-compliant Product will not be serviced. Further, the sender will
be responsible for arranging return shipment of the un-serviced Product, through a carrier of
the sender's choice and at the sender's expense. Horizon will hold non-compliant Product for
a period of 60 days from notification, after which it will be discarded.
DYNC3015
WARRANTY AND SERVICE CONTACT INFORMATION
Horizon Hobby
Contact Information
DYNAMITE P1 MINI
Horizon Service Center
servicecenter.horizonhobby.com/RequestForm/
DYNC3015
(Repairs and Repair Requests)
Horizon Product Support
DYNC3015
(Product Technical Assistance)
877-504-0233
DYNC3015
Sales
800-338-4639
Horizon Technischer Service
READ THE MANUAL?
Sales: Horizon Hobby GmbH
+49 (0) 4121 2655 100
DYNC3015
PRESS>TO CONFIRM
FCC INFORMATION
DYNC3015
DYNC3015
NiMH Sensitivity
Rest Time
NiCd Sensitivity
ON
CHG>DCHG
Celcius
10Min
D.Peak
CHG>DCHG
10Min
4mV
D.Peak
Rest Time
Temperature Unit
NiMH Sensitivity
Capacity Cut-Off
CHG>DCHG
10Min
Celcius
Rest Time
NiMH Sensitivity
NiCd Sensitivity
Key Beep
ON
5000mAh
D.Peak
4mV
CHG>DCHG
10Min
D.Peak
4mV
D.Peak
4mV
Buzzer
NiMH Sensitivity
Saftety Timer
Rest Time
NiMH Sensitivity
NiCd Sensitivity
Temp Cut-Off
D.Peak
4mV
ON
CHG>DCHG
120Min
10Min
NiCd Sensitivity
Key Beep
Bal. Connection
ON
On
50C 122F
D.Peak
4mV
D.Peak
4mV
D.Peak
Buzzer
4mV
ON
NiCd Sensitivity
Capacity Cut-Off
NiMH Sensitivity
Temperature Unit
Key Beep
ON
NiCd Sensitivity
D.Peak
ON
D.Peak
4mV
5000mAh
4mV
Key Beep
Bal. Connection
ON
Load Factory Set
Celcius
Buzzer
ON
D.Peak
4mV
Buzzer
ON
ON
Key Beep
NiCd Sensitivity
ON
Temp Cut-Off
Bal. Connection
Buzzer
Rest Time
ON
Key Beep
On
50C 122F
ON
D.Peak
4mV
Bal. Connection
Load Factory Set
Version
CHG>DCHG
ON
Buzzer
ON
ON
Enter
HW:1.00
SW:1.03
Bal. Connection
Temperature Unit
Key Beep
ON
NiMH Sensitivity
Load Factory Set
ON
Bal. Connection
Buzzer
Celcius
ON
Load Factory Set
Version
D.Peak
Enter
ON
Enter
HW:1.00
SW:1.03
Load Factory Set
Bal. Connection
Rest Time
NiCd Sensitivity
Version
Enter
ON
Load Factory Set
CHG>DCHG
10Min
Version
BATT/PROGRAM
HW:1.00
SW:1.03
D.Peak
Enter
HW:1.00
SW:1.03
BATT MEMORY
NiMH Sensitivity
Version
Load Factory Set
Key Beep
HW:1.00
D.Peak
SW:1.03
4mV
Version
Enter
BATT/PROGRAM
Buzzer
HW:1.00
SW:1.03
BATT MEMORY
ON
NiCd Sensitivity
[ BATT MEMORY X ]
Version
Bal. Connection
ON
BATT/PROGRAM
D.Peak
HW:1.00
SW:1.03
4mV
ENTER SET->
BATT/PROGRAM
BATT MEMORY
BATT MEMORY
BATT/PROGRAM
[ BATT MEMORY X ]
Key Beep
ON
ON
Load Factory Set
Buzzer
BATT MEMORY
ON
BATT/PROGRAM
ENTER SET->
[ BATT MEMORY X ]
BATT MEMORY
[ BATT MEMORY X ]
Bal. Connection
BATT/PROGRAM
ENTER SET->
Version
ON
ENTER SET->
BATT MEMORY
[ BATT MEMORY X ]
HW:1.00
SW:1.03
[ BATT MEMORY X ]
ENTER SET->
Load Factory Set
ENTER SET->
Enter
[ BATT MEMORY X ]
ON
ENTER SET->
ON
Version
BATT/PROGRAM
HW:1.00
SW:1.03
BATT MEMORY
BATT TYPE
ON
LiPo
BATT VOLTAGE
[ BATT MEMORY X ]
BATT/PROGRAM
14.8V(4S)
ENTER SET->
BATT TYPE
BATT MEMORY
BATT TYPE
LiPo
CHARGE CURRENT
BATT TYPE
LiPo
2.0A
LiPo
BATT VOLTAGE
BATT VOLTAG
[ BATT MEMORY X ]
DISCHRG CURRENT
BATT VOLTAGE
14.8V(4S)
ENTER SET->
1.0A
14.8V(4S)
CHARGE CURRENT
CHARGE CURR
2.0A
DISCHG VOLTAGE
ON
CHARGE CURRENT
3.0V/CELL
2.0A
ON
DISCHRG CURRENT
DISCHRG CUR
DYNAMITE P1 MINI
TVC=YOUR RISK!
1.0A
DISCHRG CURRENT
DYNC3015
4.20V
BATT TYPE
1.0A
ON
DISCHG VOLTAGE
DYNAMITE P1 MINI
DISCHG VOLT
LiPo
SAVE PROGRAM
3.0V/CELL
DISCHG VOLTAGE
DYNC3015
BATT VOLTAG
ENTER
3.0V/CELL
DYNAMITE P1 MINI
TVC=YOUR RISK!
TVC=YOUR RI
DYNAMITE P1 MINI
READ THE MANUAL?
TVC=YOUR RISK!
DYNC3015
4.20V
DYNC3015
PRESS>TO CONFIRM
DYNAMITE P1 MINI
CHARGE CURR
4.20V
SAVE PROGRAM
DYNAMITE P1 MINI
DYNC3015
SAVE PROGRA
READ THE MANUAL?
BATT TYPE
ENTER
SAVE PROGRAM
DYNC3015
PRESS>TO CONFIRM
LiPo
DYNAMITE P1 MINI
DISCHRG CUR
ENTER
READ THE MANUAL?
DYNC3015
READ THE MANUAL?
BATT VOLTAGE
PRESS>TO CONFIRM
PRESS>TO CONFIRM
14.8V(4S)
READ THE MANUAL?
DISCHG VOLT
BATT TYPE
READ THE MANUAL?
PRESS>TO CONFIRM
CHARGE CURRENT
LiPo
PRESS>TO CONFIRM
2.0A
READ THE MANUAL?
TVC=YOUR RI
BATT VOLTAGE
DYNAMITE P1 MINI
BATT TYPE
PRESS>TO CONFIRM
DISCHRG CURRENT
14.8V(4S)
DYNC3015
LiPo
BATT TYPE
1.0A
SAVE PROGRA
CHARGE CURRENT
LiPo
BATT VOLTAG
BATT TYPE
DISCHG VOLTAGE
2.0A
LiPo
BATT VOLTAGE
3.0V/CELL
DYNAMITE P1 MINI
DISCHRG CURRENT
14.8V(4S)
BATT TYPE
READ THE MANUAL?
CHARGE CURR
BATT VOLTAGE
DYNC3015
TVC=YOUR RISK!
1.0A
LiPo
PRESS>TO CONFIRM
14.8V(4S)
CHARGE CURRENT
4.20V
DISCHG VOLTAGE
BATT VOLTAGE
2.0A
DISCHRG CUR
CHARGE CURRENT
SAVE PROGRAM
3.0V/CELL
BATT TYPE
14.8V(4S)
2.0A
DISCHRG CURRENT
ENTER
READ THE MANUAL?
LiPo
TVC=YOUR RISK!
1.0A
CHARGE CURRENT
DISCHG VOLT
DISCHRG CURRENT
PRESS>TO CONFIRM
4.20V
BATT VOLTAGE
2.0A
1.0A
DISCHG VOLTAGE
BATT TYPE
14.8V(4S)
SAVE PROGRAM
DISCHRG CURRENT
3.0V/CELL
TVC=YOUR RI
LiPo
DISCHG VOLTAGE
ENTER
CHARGE CURRENT
1.0A
TVC=YOUR RISK!
3.0V/CELL
BATT VOLTAGE
2.0A
4.20V
SAVE PROGRA
DISCHG VOLTAGE
TVC=YOUR RISK!
14.8V(4S)
DISCHRG CURRENT
3.0V/CELL
4.20V
SAVE PROGRAM
CHARGE CURRENT
1.0A
TVC=YOUR RISK!
ENTER
2.0A
SAVE PROGRAM
4.20V
DISCHG VOLTAGE
ENTER
DISCHRG CURRENT
3.0V/CELL
SAVE PROGRAM
1.0A
TVC=YOUR RISK!
5-14-2015
ENTER
DISCHG VOLTAGE
4.20V
3.0V/CELL
Address
SAVE PROGRAM
TVC=YOUR RISK!
ENTER
4.20V
1608 Interstate Drive
Champaign, Illinois, 61822 USA
SAVE PROGRAM
ENTER
Hanskampring 9
D 22885 Barsbüttel, Germany
Created 06/2018 | 58458
120Min
4mV
ON
ON
ON
Enter
10Min
4mV
4mV
ON
ON
ON
Enter
14.8
3.0V/
14.8
3.0V/
14.
3.0V