Galanz W60B1A401J-AE5 Kullanıcı Kılavuzu - Sayfa 4

Bulaşık Makinesi Galanz W60B1A401J-AE5 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Galanz W60B1A401J-AE5 15 sayfaları.

Sayfayı Yazdır

Dishwasher Features

4．Prior Using for the First Time

Before using your dishwasher for the first time:

A. Set the water softener

B. Pour 500ml of water inside the salt container and then fill with dishwasher salt

C. Fill the rinse aid dispenser

D. Function of detergent

A. Water Softener

The water softener is designed to remove minerals and salts from the water, which would have a

detrimental or adverse effect on the operation of the appliance. The higher the content of these

minerals and salts, the harder the water is. The softener should be adjusted according to the

hardness of the water in your area. Your local Water Authority can advise you on the hardness of

the water in your area.

Setting

The amount of salt dispensed can be set from H0 to H7.

Salt is not required at the set value H0.

1. Find out about the hardness value of your tap water. Your water utility company will help you

with this.

2. Set value can be found in the water hardness table.

3. Close the door.

4. Switch on "Power" switch.

5. Hold down " Delay" button and then press "Program" button for 5 seconds.The buzzer rings

one time and H..

flashes on the digital display.(factory setting is H4)

Front View

1 Upper Basket

2 Spray Arms

3 Lower Basket

4 Water Softener

5 Detergent Dispenser

6 Rinse Aid Dispenser

7 Cutlery Tray

8 Cup Holder

To change the setting:

1. Press " Delay " button.

Each time the button is pressed, the set value

increasesby one level;when the value of H7 has

been reached, the display jumps back to H0(off).

2. Press " Program " button. The chosen setting

has now been stored.

Contact your local water board for infor-

mation on the hardness of your water

supply.

B. Loading the Salt into the Softener

Always use salt intended for using with dishwasher.

NOTE: If your model has no water softener, you may skip this section

WATER SOFTENER

The hardness of the water varies from place to place. If hard water is used in the

dishwasher, deposits will form on the dishes and utensils.

The appliance is equipped with a special softener that uses salts specifically

designed to eliminate lime and minerals from the water.

The salt container is located beneath the lower basket and should be filled as follows:

Attention!

Only use salt specifically designed for use in dishwashers! All other types of salt not specifically

designed for use in a dishwasher, especially table salt, will damage the water softener. In case of

damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is

liable for any caused damages.

Only fill with salt just before starting one of the complete washing programmes.

This will prevent any grains of salt or salty water, which may have been split, remaining on the

bottom of the machine for any period of time, which may cause corrosion.

After the first wash cycle the control panel light expires.

A. Remove the lower basket and then unscrew and remove the cap from the salt container.

B. If you are filling the container for the first time, fill 2/3 of its volume with water (around 500ml).

Water hardness table

Water hardness

Set value on

Mmol/l

the machine

Clark

Range

0-8

soft

0-1.1

9-10

soft

1.2-1.4

11-12

medium

1.5-1.8

13-15

medium

1.9-2.1

16-20

medium

2.2-2.9

21-26

hard

3.0-3.7

27-38

hard

3.8-5.4

39-62

hard

5.5-8.9