Hifonics XXV XXV Juno Kullanıcı Kılavuzu - Sayfa 11
Amplifikatör Hifonics XXV XXV Juno için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Hifonics XXV XXV Juno 20 sayfaları. Xxv edition high performance amplifier
Sayfayı Yazdır
XXV COLOSSUS DUAL MONO BLOCK AMPLIFIER APPLICATIONS
BASIC APPLICATION
The Dual Mono Block amplifiers are capable of 4, 2 & 1 Ohm stereo and 4 & 2
bridged loads and can be used in any of the "bi-amplifier" systems described
in the XXV-Juno and XXV-Gemini directions.
The XXV-Colossus has two 1600 watt D-Class channels built-in labeled
L & R on the end panel.
SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts
with good quality RCA interconnect cables.
2. Plug in the XXVR-1 bass remote module into the amp REMOTE INPUT jack.
3. Route a 2 gauge power cable directly to the vehicle battery with an in-line 300 amp fuse.
FULL RANGE
STEREO LINE INPUT
Y-ADAPTOR
NOT USED
DESIGNATED MONO
LINE INPUT
-6dB
XXVR-1
DIAGNOSTICS
CLIP
GREEN: POWER
GREEN: PRE-CLIP
AMBER: THERMAL
AMBER: SOFT CLIP
-20dB
0dB
RED: SHORT
RED: HARD CLIP
BASS REMOTE
FULL RANGE
STEREO LINE INPUT
Y-ADAPTOR
NOT USED
DESIGNATED MONO
LINE INPUT
-6dB
XXVR-1
DIAGNOSTICS
CLIP
GREEN: POWER
GREEN: PRE-CLIP
AMBER: THERMAL
AMBER: SOFT CLIP
-20dB
0dB
RED: SHORT
RED: HARD CLIP
BASS REMOTE
This will allow you to operate separate subs independently (on each channel L
or R) at 4, 2 or 1 Ohm at up to 1600 watts or bridged across L & R to operate a
single sub up to 3200 watts at 4 or 2 Ohms.
Note: The amp is not capable of 1 Ohm when bridged across L & R.
The crossovers and XXVR-1 Bass Remote Module will operate both L & R
channels simultaneously.
USING CHANNELS L & R INDEPENDENTLY
Note: You can use the Radio/CD designated mono
line output or a full range stereo line output.
For full range stereo line output, you will need an
optional "Y-Adaptor" as shown
USING CHANNELS L & R BRIDGED
Note: You can use the Radio/CD designated mono
line output or a full range stereo line output.
For full range stereo line output, you will need an
optional "Y-Adaptor" as shown
4. Connect a 2 gauge ground cable directly to chassis ground with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
Note: The amplifier is capable of
4, 2 & 1 Ohms per channel in this
configuration
REMOTE TURN-ON
CHASSIS GROUND
TO BATTERY +12v VIA
300 AMP FUSE
Note: The amplifier is capable of
4 & 2 Ohms in this configuration.
It is not capable of 1 Ohm.
BRIDGED MONO
SUBWOOFER
2 OHM MINIMUM
REMOTE TURN-ON
CHASSIS GROUND
TO BATTERY +12v VIA
300 AMP FUSE
9