Hifonics ZG-600.4 Hızlı Başlangıç Kurulum Kılavuzu
Amplifikatör Hifonics ZG-600.4 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kurulum Kılavuzu indirin. Hifonics ZG-600.4 2 sayfaları.
Sayfayı Yazdır
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
Power cable size
Model
and fusing
It is critical to use the proper power
ZG-1200.2
and ground cable. Select the size
ZG-600.4
Always use high quality copper
ZG-1200.4
cable. Visit our website for multi amp
ZG-1200.1D
system cable recommendations.
ZG-1800.1D
ZG-2400.1D
Be sure to use the proper fuse size
ZG-3200.1D
for each model. Some models require
an external fuse.
Installation
Disconnect
1
negative battery
terminal
Place terminal in a secure
position so that it won't
accidentally contact the
negative battery post
Run Cables
2
Properly route power,
speaker and RCA cables
through the vehicle.
3
Choose a mounting location
that will provide adequate air
a secure surface. Do not mount
Chassis Ground
4
The chassis ground connection
is critical to the performance
location that is close to the
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Negative Power
5
Fuse Size
Cable Size
Connection
40A x 1
Attach the chassis ground
40A x 1
50A x 1
negative terminal. It is
4ga
60A x 1
important to make sure this
80A x 1
connection is very tight.
1
00A x 1
External 150A
Remote Turn-on
6
Connection
Attach the remote turn on
output of the source unit.
Positive Power
7
Connection
Attach the main power cable
cable must run directly to
the battery and be properly
fused and be very tight.
Signal Input
8
Connection
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
Level Control
9
All manuals and user guides at all-guides.com
Bare metal
BRIDGED
BRIDGED
LEFT
RIGHT
CH 3
SPEAKER
OUTPUT
SPEAKER
BRIDGED
BRIDGED
LEFT
RIGHT
CH 1
SPEAKER
OUTPUT
SPEAKER
BRIDGED
CH 3
SPEAKER
Turn the LEVEL control completely
INPUT
LEVEL
counter-clockwise to minimum.
9V
0.2V
PHASE
BRIDGED
BRIDGED
Speaker
10
BRIDGED
Connections
LEFT
RIGHT
Connect the speaker cables to
the speaker output connectors.
SPEAKER
OUTPUT
Follow the diagram below
Stereo
BRIDGED
LEFT
RIGHT
BRIDGED
BRIDGED
LEFT
RIGHT
CH 4
CH 3
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
Monoblock
single woofer
BRIDGED
BRIDGED
LEFT
RIGHT
CH 1
CH 2
CH 4
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
OUTPUT
BRIDGED
LEFT
CH1/2
RIGHT
BRIDGED
CH 3
CH 4
CH 2
Positive Battery
11
SPEAKER
OUTPUT
Connection
SPEAKER
OUTPUT
OUTPUT
SPEAKER
OUTPUT
Connect the power cable to the
SPEAKER
OUTPUT
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
CH 1
CH 2
Be prepared to disarm your vehicle's alarm and
to enter your radio / source unit code.
CH 4
BRIDGED
BRIDGED
LEFT
CH1/2
RIGHT
LEFT
CH3/4
RIGHT
Re-connect
12
SPEAKER
OUTPUT
Negative Battery
Terminal
OUTPUT
XOVER
MODE
INPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
Re-connect the negative
SPEAKER
LEVEL
SUBSONIC
SUBSONIC
battery terminal making sure it
is securely tightened.
FULL
HP
MONO STEREO
15
35Hz
10
40Hz
LP
6V
0.2V
XOVER
MODE
LPF
LPF
LPF
BRIDGED
CH 3
CH 4
SPEAKER
OUTPUT
SPEAKER
OUTPUT
Bridged
BRIDGED
BRIDGED
CH 1
CH 2
LEFT
RIGHT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
BRIDGED
CH 3
CH 4
Monoblock
LEFT
RIGHT
multiple woofers
BRIDGED
LEFT
RIGHT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
BRIDGED
LEFT
CH3/4
RIGHT
LEFT
CH3/4
RIGHT
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
LEFT
CH1/2
RIGHT
CH 3
CH 4
CH 5
SPEAKER
OUTPUT
BRIDGED
LEFT
CH3/4
RIGHT
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
OUTPUT
Speakers
Subwoofer
CH 1
CH 2
CH 3
BRIDGE
CH 3
BRIDGE
CH 1
BRIDGE
CH 3
BRIDG
LEFT
CH3