Autonics TCN Series Ürün Kılavuzu - Sayfa 2

Sıcaklık Kontrolörü Autonics TCN Series için çevrimiçi göz atın veya pdf Ürün Kılavuzu indirin. Autonics TCN Series 6 sayfaları. Dual display pid temperature controller
Ayrıca Autonics TCN Series için: Manuel (13 sayfalar)

Sayfayı Yazdır

Cautions during Use

• Follow instructions in 'Cautions during Use' . Otherwise, it may cause unexpected

accidents.

• Check the polarity of the terminals before wiring the temperature sensor.

• For RTD temperature sensor, wire it as 3-wire type, using cables in same thickness and

length. For thermocouple (TC) temperature sensor, use the designated compensation

wire for extending wire.

• Keep away from high voltage lines or power lines to prevent inductive noise. In case

installing power line and input signal line closely, use line filter or varistor at power line

and shielded wire at input signal line. Do not use near the equipment which generates

strong magnetic force or high frequency noise.

• Install a power switch or circuit breaker in the easily accessible place for supplying or

disconnecting the power.

• Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature

controller.

• When changing the input sensor, turn off the power first before changing. After

changing the input sensor, modify the value of the corresponding parameter.

• 24 VACᜠ, 24-48 VDCᜡ power supply should be insulated and limited voltage/current

or Class 2, SELV power supply device.

• Make a required space around the unit for radiation of heat. For accurate temperature

measurement, warm up the unit over 20 min after turning on the power.

• Make sure that power supply voltage reaches to the rated voltage within 2 sec after

supplying power.

• Do not wire to terminals which are not used.

• This unit may be used in the following environments.

- Indoors (in the environment condition rated in 'Specifications')

- Altitude Max. 2,000 m

- Pollution degree 2

- Installation category II

Ordering Information

This is only for reference, the actual product does not support all combinations.

For selecting the specified model, follow the Autonics website .

❶

❶ Size

S: DIN W 48 × H 48 mm

M: DIN W 72 × H 72 mm

H: DIN W 48 × H 96 mm

L: DIN W 96 × H 96 mm

❷ Power supply

2: 24 VACᜠ 50/60 Hz, 24-48 VDCᜡ

4: 100-240 VACᜠ 50/60 Hz

Product Components

• Product

• Bracket

Sold Separately

• Terminal protection cover: RSA / RMA / RHA / RLA Cover

❷

❸

❸ Wiring type

No mark: Bolt

P: Connector plug connection

• Instruction manual

Specifications

Series

TCN4□-22□-□

24 VACᜠ 50/60 Hz ±10%

Power supply

24 - 48 VDCᜡ ±10%

Power consumption AC: ≤ 5 VA, DC: ≤ 3 W

Sampling period

100 ms

Input specification

Refer to 'Input Type and Using Range.

Relay

250 VACᜠ 3A, 30 VDCᜡ 3A, 1a

Control

output

SSR

12 VDCᜡ±2 V, ≤ 20 mA

Alarm output

250 VACᜠ 1 A 1a

Display type

7 Segment (red, green), LED type

Control

Heating,

ON/OFF, P, PI, PD, PID Control

type

Cooling

Hysteresis

1 to 100 (0.1 to 50.0) ℃/℉

Proportional band

0.1 to 999.9 ℃/℉

(P)

Integral time (I)

0 to 9,999 sec

Derivative time (D)

0 to 9,999 sec

Control cycle (T)

0.5 to 120.0 sec

Manual reset

0.0 to 100.0%

Mechanical ≥ 5,000,000 operations

Relay

life

OUT1/2: ≥ 200,000 operations (load resistance: 250 VACᜠ 3 A )

Electrical

cycle

AL1/2: ≥ 300,000 operations (load resistance: 250 VACᜠ 1 A )

Between input terminal and

Dielectric strength

power terminal: 1,000 VACᜠ

50/60 Hz for 1 min

0.75 mm amplitude at frequency of 5 to 55 Hz (for 1 min) in each X, Y, Z

Vibration

direction for 2 hours

Insulation

≥ 100 MΩ (500 VDCᜡ megger)

resistance

±2 kV square shaped noise (pulse width: 1 ㎲) by noise simulator

Noise immunity

R-phase, S-phase

≈ 10 years (non-volatile semiconductor memory type)

Memory retention

Ambient

-10 to 50 ℃, storage: -20 to 60 ℃ (no freezing or condensation)

temperature

Ambient humidity

35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)

Mark: ▱, double or reinforced

insulation (dielectric strength

Insulation type

between the measuring input

part and the power part: 1 kV)

Approval

ᜢ ᜧ ᜫ

• TCN4S: ≈ 100 g (≈ 147 g)

Unit weight

(packaged)

• TCN4H: ≈ 124 g (≈ 194 g)

TCN4□-24□-□

100 - 240 VACᜠ 50/60 Hz ±10%

≤ 5 VA

Between input terminal and power

terminal: 2,000 VACᜠ 50/60 Hz for 1

min

Mark: ▱, double or reinforced

insulation (dielectric strength

between the measuring input part

and the power part: 2 kV)

• TCN4M: ≈ 133 g (≈ 203 g)

• TCN4L: ≈ 179 g (≈ 275 g)