Autonics TM Series Ürün Kılavuzu
Sıcaklık Kontrolörü Autonics TM Series için çevrimiçi göz atın veya pdf Ürün Kılavuzu indirin. Autonics TM Series 4 sayfaları. Modular 4-channe pid temperature controllers with screwless connector
Ayrıca Autonics TM Series için: Manuel (9 sayfalar)
Sayfayı Yazdır
TCD210160AC_MODI
Modular 2/4-Channel PID
Temperature Controllers
with Screwless Connector
TM Series
PRODUCT MANUAL
For your safety, read and follow the considerations written in the instruction
manual, other manuals and Autonics website.
The specifications, dimensions, etc are subject to change without notice for product
improvement Some models may be discontinued without notice.
Features
• Multi-channel (4-channel : TM4/2-channel : TM2) input and output control
• High-speed sampling cycle (4-channel : 100ms/2-channel : 50ms)
• Module connection and expansion with expansion connectors
- Communication between modules
- No additional power supply wiring
- Expandable up to 31 units (124-channels/62-channels)
• Simultaneous heating and cooling control function
• Isolated input channels (dielectric strength : 1000VAC)
• Switch between current output and SSR drive output (TM2- 2C)
• Parameter configuration via PC (USB and RS485 communication)
- DAQMaster software included (comprehensive device management software)
- Communication converter sold separately : SCM-US (USB to serial converter), SCM-
38I (RS-232C to RS485 converter), SCM-US48I (USB to RS485 converter)
• Easy wiring and maintenance with various connectors : sensor input connector,
control output connector, power/communication connector
• Heater disconnect alarm function (CT input)
- Current transformer (CT) sold separately : CSTC-E80LN, CSTC-E200LN
• Various input types and temperature ranges
ᜢ ᜧ ᜣ ᜫ
Safety Considerations
• Observe all 'Safety Considerations' for safe and proper operation to avoid hazards.
• symbol indicates caution due to special circumstances in which hazards may occur.
Warning
Failure to follow instructions may result in serious injury or death
01. Fail-safe device must be installed when using the unit with machinery that
may cause serious injury or substantial economic loss. (e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, economic loss or fire.
02. Do not use the unit in the place where flammable/explosive/corrosive gas,
high humidity, direct sunlight, radiant heat, vibration, impact or salinity
may be present.
Failure to follow this instruction may result in explosion or fire.
03. Install on a device panel to use.
Failure to follow this instruction may result in fire.
04. Do not connect, repair, or inspect the unit while connected to a power
source.
Failure to follow this instruction may result in fire.
05. Check 'Connections' before wiring.
Failure to follow this instruction may result in fire.
06. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire.
Caution
Failure to follow instructions may result in injury or product damage
01. When connecting the power input and relay output, use AWG 26 to 12
cable and connecting the sensor input and communication cable without
dedicated cable, use AWG 28 to 14 cable.
Failure to follow this instruction may result in fire or malfunction due to contact
failure.
02. Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage
03. Use a dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire or electric shock.
04. Keep the product away from metal chip, dust, and wire residue which flow
into the unit.
Failure to follow this instruction may result in fire or product damage.
Cautions during Use
• Follow instructions in 'Cautions during Use'. Otherwise, it may cause unexpected
accidents.
• Check the polarity of the terminals before wiring the temperature sensor.
For RTD temperature sensor, wire it as 3-wire type, using cables in same thickness and
length.
For thermocouple (CT) temperature sensor, use the designated compensation wire for
extending wire.
• Keep away from high voltage lines or power lines to prevent inductive noise.
In case of installing power line and input signal line closely, use line filter or varistor at
power line and shielded wire at input signal line.
Do not use near the equipment which generates strong magnetic force or high
frequency noise.
• Do not apply excessive power when connecting or disconnecting the connectors of
the product.
• Install a power switch or circuit breaker in the easily accessible place for supplying or
disconnecting the power.
• Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature
controller.
• When changing the input sensor, turn off the power first before changing.
After changing the input sensor, modify the value of the corresponding parameter.