Hifonics MT Olympus Jupiter 1.5k Hızlı Kılavuz - Sayfa 3

Araba Amplifikatörü Hifonics MT Olympus Jupiter 1.5k için çevrimiçi göz atın veya pdf Hızlı Kılavuz indirin. Hifonics MT Olympus Jupiter 1.5k 12 sayfaları. Mt olympus

Sayfayı Yazdır
Hifonics MT Olympus Jupiter 1.5k Hızlı Kılavuz

AMPLIFIER FEATURE DESCRIPTIONS

MT OLYMPUS AMPLIFIERS:
This is a unique series of amplifiers regarding channel stability and design.
The COLOSSUS and COLOSSUS PRO are stable at 4/2/1-Ohm per channel and 4/2-Ohms bridged.
The BOLTAR and JUPITER are stable at 4/2-Ohms per channel and 4-Ohms bridged.
The HERCULES and ATLAS is stable at 4/2/1-Ohm.
The input sensitivities for rated output powers are variable from 0.2V to 9V.
All crossovers are fully variable in their respective ranges.
Crossover filters are 12dB/Octave.
FEATURES FOR BOLTAR / COLOSSUS PRO / JUPITER:
X-OVER:
-FULL RANGE: Bypasses all frequency adjustments except Subsonic.
-HP: High Pass operation uses Subsonic to cutoff the low frequencies and the FREQUENCY
adjustment can be used to create a sharper cutoff on the low end.
-LP/BP: Low Pass/Band Pass operation which allows for use of the Subsonic and Frequency
(Low Pass) shaping controls.
LOW PASS X-OVER:
-LP/BP STEREO 12dB/OCT: Stereo operation with a smooth 12dB/octave rolloff.
-LP DIRECT MONO 24dB/OCT: Bridged operation with a sharp 24dB/octave cutoff.
SUBSONIC FILTER: Low frequency cutoff variable from 15Hz to 150Hz.
PARAMETRIC EQ:
-X1 or X10 FREQUENCY MULTIPLIER: Multiplies frequency of enhancement in PARAMETRIC EQ.
-FREQUENCY: Variable enhancement from 40Hz to 400Hz at X1 or 400Hz to 4000Hz at X10.
-BANDWIDTH: Narrow to Wide range enhancements above and below the center FREQUENCY.
-CUT/BOOST: -10 to +10 enhancements centered at the FREQUENCY selected.
FREQUENCY: Variable from 40Hz to 400Hz at X1 and 400Hz to 4000Hz at X10 enhancement on
the multiplier. This FREQUENCY function varies based on the X-OVER selections described above.
PHASE: Variable time alignment from 0 to 180 degrees for both LEFT and RIGHT channels.
INPUT LEVEL: Variable from 0.2V to 9V.
FULL RANGE OUTPUT: Passes RCA signal through the amplifier unchanged by settings.
LINE INPUT: RCA Inputs.
FEATURES FOR JUPITER ONLY:
MODE: Internal routing of RCA signal. Selecting 2CH indicates RCA's are being connected to Channel
1&2 Inputs and the amplifier will internally route signal to Channels 3&4. Selecting 4CH indicates RCA's
are being connected to Channel Inputs on 1-4.
FEATURES FOR COLOSSUS / HERCULES / ATLAS:
LINE INPUT: RCA Inputs
FULL RANGE OUTPUT: Passes RCA signal through the amplifier unchanged by settings.
INPUT LEVEL: Variable from 0.2V to 9V.
PHASE: Variable time alignment from 0 to 180 degrees.
PARAMETRIC EQ:
-FREQUENCY: Variable enhancement from 30Hz to 100Hz.
-BANDWIDTH: Narrow to Wide range enhancements above and below the center FREQUENCY.
-BOOST: 0 to +10 enhancements centered at the FREQUENCY selected.
SUBSONIC FILTER: Low frequency cutoff variable from 15Hz to 35Hz.
LOW PASS FILTER: High frequency cutoff variable from 35Hz to 250Hz.
MODE (HERCULES/ATLAS ONLY):
-MASTER OUT: Factory setting for the switch location when using the amp alone. Also used when
linking a pair of HERCULES/ATLAS amplifier at 2-Ohms. When in MASTER OUT position, a single
RCA can be connected to the MASTER OUT RCA receptacle to provide signal to the SLAVE INPUT
on the SLAVE amplifier.
-SLAVE IN: Your MODE switch should only be in this position if you are linking a pair of
HERCULES/ATLAS amplifiers and this amp is the SLAVE. At that point the SLAVE amp will receive
the single RCA on the SLAVE IN. No other RCA's can be connected to your amplifier other than
SLAVE IN when in SLAVE IN position.
BALANCED INPUT (COLOSSUS ONLY): DIN connection which is a step above the standard RCA
signal as it accepts from 0.4V to 18V.
A POWER LED indicates the powered up and turned on condition.
All HIFONICS amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,
and amplifier DC faults indicated by the red "PROTECT" LED.
CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU
WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE
WARRANTY PRINTED IN THE BACK OF THE MANUAL.
BOLTAR / COLOSSUS PRO 2-CHANNEL AMPLIFIERS
LP/BP
FULL RANGE
STEREO 12dB/OCT
SUBSONIC
HP
LP/BP
MONO 24dB/OCT
15Hz
150Hz
LP DIRECT
DIAGNOSTIC
RED-SHORT CIRCUIT
AMBER-THERMAL
RED-CLIP
HFR-G1
AMBER-NEAR CLIP
40Hz
400Hz
REMOTE
FREQUENCY
GREEN-PRE CLIP
JUPITER 4-CHANNEL AMPLIFIERS
CROSSOVER
4Ch
HFR-G1
MONO MIX
HP
LP/BP
X10
OUTPUT
REMOTE
FREQUENCY
FULL RANGE
X1
40Hz
400Hz
HP
X10
DIAGNOSTIC
RED-SHORT CIRCUIT
AMBER-THERMAL
RED-CLIP
FULL
X1
AMBER-NEAR CLIP
40Hz
400Hz
GREEN-PRE CLIP
FREQUENCY
These amplifiers feature two DIAGNOSTIC LED's.
One monitors Short Circuits and Thermal Protection while
the second monitors Clipping status.
HERCULES / ATLAS MONO AMPLIFIERS
LINE
FULL RANGE
INPUT
OUTPUT
LEVEL
PHASE
BOOST
BANDWIDTH
L
L
9V
0.2V
0
180 0dB
+10dB NARROW WIDE 30Hz
PARAMETRIC BASS EQ
R
R
COLOSSUS DUAL MONO AMPLIFIERS
LINE
FULL RANGE
BALANCED
INPUT
OUTPUT
INPUT
LEVEL
PHASE
BOOST
L
L
9V
0.2V
0
180 0dB
R
R
These amplifiers feature two DIAGNOSTIC LED's.
One monitors Short Circuits and Thermal Protection while
the second monitors Clipping status.
PARAMETRIC EQ
FULL RANGE
LINE
FREQUENCY
BANDWIDTH
CUT/BOOST
OUTPUT
INPUT
L
L
X1
X10
40Hz
400Hz Narrow Wide -10dB
+10dB
R
R
X1
X10
0
180
0
180
9V
0.2V
RIGHT
LEFT
INPUT LEVEL
PHASE
PARAMETRIC EQ
CH 3&4
X10
LINE INPUT
FREQUENCY
BANDWIDTH
BOOST
SUBSONIC
LEVEL
Ch1
Ch3
X1
40Hz
400Hz NARROW WIDE -10dB +10dB 15Hz
150Hz 9V
0.2V
X10
2CH
X1
Ch2
Ch4
40Hz
400Hz NARROW WIDE -10dB +10dB
9V
0.2V
4CH
FREQUENCY
BANDWIDTH
BOOST
LEVEL
MODE
CH 1&2
PARAMETRIC EQ
MODE
SLAVE IN
MASTER
DIAGNOSTIC
FREQUENCY
SUBSONIC
LOW PASS
OUT
RED-SHORT CIRCUIT
AMBER-THERMAL
MASTER OUT
100Hz
HFR-G1
15Hz
35Hz 35Hz
250Hz
REMOTE
RED-CLIP
AMBER-NEAR CLIP
GREEN-PRE CLIP
SLAVE
IN
DIAGNOSTIC
BANDWIDTH
FREQUENCY
SUBSONIC
LOW PASS
RED-SHORT CIRCUIT
AMBER-THERMAL
HFR-G1
+10dB NARROW WIDE 30Hz
100Hz
15Hz
35Hz 35Hz
250Hz
REMOTE
PARAMETRIC BASS EQ
RED-CLIP
AMBER-NEAR CLIP
GREEN-PRE CLIP